64E-3CKXW (20X) Magic Chef Range - Instructions

Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.

was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!

2 screws easy to remove and plug in the wire. job done.

the igniter would glow but the gas would not flow...
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.

Un-did the old one put in the new. Iam 63 years old and a woman. Repair men wanted 500.00 plus to come out and repair I did it for cost of igniter in 15 min. Oven works great! Thanks parts select for making it so easy!

Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.

unplugged the oven, unplugged the ignitor and removed the two screws

First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took about 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)

A very common problem for ovens not heating up is the oven igniter going bad. Depending on how much you use your oven, they only last about 5 years. It is easy to replace, but getting it off can be a little tricky since the screws are exposed to so much heat. Once you got it off, you can unclip the old one and clip the new one right in. Then bolt it back on, throw in the racks and shelves, and start cooking. I replaced the igniter twice, the temperature sensor once, and the control panel once.

remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

Fist I removed the screws on the front-sides of the oven. Then I turned off the gas, by adjusting the in-line valve. I then unscrewed the gas fitting going into the bottom of the oven. I pulled the oven out, being careful not to put too much pull on the electrical cord. I put a bench in front of the oven and set it down.
I then removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!

Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason it did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!

During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.

My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!