LRE3085ST LG Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from CERRITOS, CA
- Parts Used:
- 4890W1N005A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Inner Oven glass because it shattered
Go onto youtube, such as https://www.youtube.com/watch?v=-ITkrwhDNMQ and watch similar videos for DYI. The process is very similar to other models.
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know the process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
Hope this helps
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know the process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
Hope this helps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CHESAPEAKE, VA
- Parts Used:
- MEE62385201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Hammer 1, Glass range top and heating element 0
Dropped a hammer on the range while removing a ceiling light. Viewed a How-To video on Google. Ordered the needed parts. Followed the steps from the How-To video. Reinstall was a bit tricky by myself - could have used an extra set of hands. I have a few words of caution:
1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet.
2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
1) Put something between the range top and range - like a sheet or drop cloth - to prevent a dropped screw from falling into a crevice in the stove. I dropped a screw and was unable to retrieve it, even with a magnet.
2) Makes sure you remove all bumpers, screws, clips, etc. from the item being replaced and put them on the new item if the new item does not come with replacement bumpers, screws, etc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SOUTH HAVEN, MI
- Parts Used:
- EBR74164801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Convection bake fan would not shut off
Looked at schematic to follow circuitry. Checked online for advice. Most online advice suggested replacing thermostat. Thermostat is not in controlling fan circuit!
PCB is only circuit controlling fan on and off. I unplugged fan so as to use rest of range until I received and installed PCB. Works fine now. Note: I have electronics background and can read most circuitry.
PCB is only circuit controlling fan on and off. I unplugged fan so as to use rest of range until I received and installed PCB. Works fine now. Note: I have electronics background and can read most circuitry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from LEXINGTON, KY
- Parts Used:
- MEE62306405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bottom heat element went out
Checked element no reading. Took off back panel and removed element. Took 5 days to get element. Put in new one. Took 20 minutes. Did not have to cut panel as video had shown. It had screws and was easy to get out and put the new one in. The new element was exactly the same as the old one. I checked all elements before ordering. Was satisfied with everything but the delivery time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from FORT WORTH, TX
- Parts Used:
- EBR64624906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Half the LEDs on my stove went out, the part fixed it.
Unplugged the stove, took the top cover off, removed the old part and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from CROSS PLAINS, WI
- Parts Used:
- AEG33897003
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
PartsSelect substituted the part and it will not work
The repair person could not complete the job as the part sent is totally wrong for the appliance. The company has not responded to me email sent 12/30/23 and there is no way to leave a voice mail or ask for a call back, due to large call volume. A live representative does not answer the phone.
Please check your emails. You ask for feedback on repair, but obviously do not take time to check emails for issues. Because the error is on the part of PartSelect I requested an RMA to return an incorrect part. Please respond by sending a shipping label so it can be returned for a refund. I have submitted a dispute with the credit card company since your company is negligent in customer service. Please email RMA shipping label to ritashimniok@gmail.com
Please check your emails. You ask for feedback on repair, but obviously do not take time to check emails for issues. Because the error is on the part of PartSelect I requested an RMA to return an incorrect part. Please respond by sending a shipping label so it can be returned for a refund. I have submitted a dispute with the credit card company since your company is negligent in customer service. Please email RMA shipping label to ritashimniok@gmail.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from NORTH BEACH, MD
- Parts Used:
- 6930W1A003X
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat needed to be replaced
We had made this determination with the help of a repairman on the phone. I ordered the part and waited for it. It was stuck in West Virginia. After several days after it was expected a repairman fixed my range to the tune of $168. It should have cost $30 (the cost of the part and shipping).
Unfortunately I probably won't order from PartSelect again.
Unfortunately I probably won't order from PartSelect again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- K R from BOISE, ID
- Parts Used:
- 4778W1N001B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken front leveler
This is a very simple repair of remove and replace. You do have to lay down the range to make it easy.
Was this instruction helpful to you?
Thank you for voting!