Models > 62109 > Instructions

62109 (KBKESEA) LG Range - Instructions

Jump to:

All Instructions for the 62109
16 - 21 of 21
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Virgil from Bowling Green, MO
Parts Used:
6549W1S011B
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Turntable not turning.
Take off cover then the bottom. Transformer is on the bottom plate and wires won't let it come all the way off, too many wires to pull off so will have to position the bottom plate so you can get to the motor. Remove 1 screw on motor and remove motor. Install new motor connect wires replace bottom plate, replace cover. All done (hope & pray it works ok) mine worked perfect. Hope this helps.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Monticello, IL
Parts Used:
6549W1S011B
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Turntable quit turning
Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joyce from Baltimore, MD
Parts Used:
3390W1G005D
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
broke glass turntable
replaced it.....very pleased with the availability and promptness of shipment...thank you....
Was this instruction helpful to you?
Thank you for voting!
Customer:
mark from crown point, IN
Parts Used:
6549W1S011B
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
synchronized motor died a terrible death and stopped turning.
Eight screws off the bottom exposed the cover plate. Easily found the motor location the looked up the item number and verified data and ordered the part. Replaced the motor, tightened the screws and flipped it upright. Plugged it in and the lights came on. Set a time pushed start and smiled! The eagle had landed!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stan from New Bedford, MA
Parts Used:
6549W1S011B
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Carousel would not turn. Small plastic drive shaft broken.
Pried cover off bottom-center of microwave. It seems to be either glued or lightly tack welded. Removed 2 small Phillips screws to remove motor. Disconnected electric feed by hand. Don't let go of electric wire or small screws. They will be hard to retrieve from behind the rest of the metal base. Reverse process to install new motor. Didn't try to put small cover back on.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kent from wichita, KS
Parts Used:
6549W1S011B
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
the turntable on the microwave quit turning even though the microwave would heat up
I removed the outer cover of the microwave and removed the bottom palte to access the small motor. i unplugged the old motor from teh wiring connector, removed (1) screw and motor came out. I reversed the proceedure with the new motor and it was finished.It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 62109
16 - 21 of 21