KGRT507FAL1 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Woodinville, WA
- Parts Used:
- WP9782065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven would not heat up/slight smell of gas
Replacing the igniter took care of the problem. I just wish I had made better notes about how the wire were routed. It would have saved time as I re-assembled everything. Th ejob itself was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Chicago, IL
- Parts Used:
- WP9782065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Kitchenaid gas oven would not heat
The stove burners and oven broiler worked fine so it was obviously something with the oven ignition. My oven is 14 years old so it made sense that the ignition would wear out. I followed the instructions provided on the PartSelect website for this repair and it worked perfectly. Very easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Weyers Cave, VA
- Parts Used:
- WP9781654
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Interior glass was broken
I watched some videos on YouTube first that said you could flip a latch on the door hinges and remove the door entirely. On this older oven there was no latch, you just open the door to its first position and lift up and out to remove the door. Unlike newer doors leave this one face up on a table to work on it. Remove all (10?) of the screws along the bottom edge, pull away the side door trim pieces, then remove the outside panel of the door by lifting slightly then pulling downwards. Mine was actually a glass panel, so be careful. Remove the two screws holding the upper door trim down onto the hinge mechanisms and rotate the trim out of the way. Lift off the large metal cover to expose the first, outer glass, then remove the insulation, then remove the screws and clips holding down the metal frame around the inner glass. Clean everything well (I used a baking soda paste), then replace in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Sandusky, OH
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Drawer Roller Snapped Off
Replaced both rollers....Quick and Easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from CHICAGO, IL
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no ignition on right frt burner
removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from San Jose, NM
- Parts Used:
- WP3184533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gasket for oven light wore out and needed replacing.
I very simply replaced the gasket where it belonged and I was good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!