KDRP407HSS4 KitchenAid Range - Instructions

I lifted the door from the oven. I reviewed the break down of the parts. The only tool needed was a screw driver to disassemble the door. I stacked each part in the order it was removed and replaced them in reverse order. PS, I cleaned the old glass before it was reinstalled it.

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.

find the owner's manual & follow the instructions for inserting two allen wrenches (assuming that you cannot find the "removal tools" that came with the oven) into the holes near the hinges on the door, carefully & slowly close the door with the wrenches inserted until the hinges disengage from the wall mounted oven. Lift the door away (is rather heavy). It is necessary to remove panels from the front one layer at a time to reach the 3rd layer of glass (the inner most glass that is the rather easy one to break). Be slow and methodical. Not a challenge once you study the owner's manual for door removal instructions.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

With some help from my wife.

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

The repair went well & the part came in on time for thanksgiving thank you

I found several posts about Whirlpool/KitchenAid ovens having this problem and most of the time this required a replacement of the thermal fuse. Other than the large number of screws to remove the oven and the sheet metal coverings, replacing the fuse was mostly about waiting to get the part. If I had a local dealer with the fuse, I probably could have been baking Deep Dark Chocolate Cheesecake that same evening. Even so, this particular repair should be left to those familiar with doing moderate-level handyman type repairs. You have to make sure the breaker is off and beware of the sharp edges on sheet metal. Fortunately, the fuse was easy to find using online documentation for my model. Part Select was very helpful when my original order did not arrive. Their customer service was great!

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

Ordered a replacement part and during installation tightened the top mounting screws too tight and shattered the replacement part. Ordered a new replacemnte part and installed without overtighting mounting screws. Repair went well. I caution others not to overtighten top mounting screws. These are same screws that attache the SS pull handle on oven door.

The replacement door has a cushion on the top and the sides secured to the tempered glass. When you tighten these brackets they can cause the entire glass panel to break. To prevent this use seven #8 flat washers per hole on the top of the door before securing the brackets. These will act as spacers but you will still will be able to achieve enough pressure to hold everything in place when you tighten them. Hope this helps, it worked for me, florida bob!!

I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy