KEDC205YWH0 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- G Weir from Ocoee, FL
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace bake element in 20 yr. old wall oven
followed the instructions. removed the old element and installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Latrecia from Antioch, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element caught on fire & broke into 2 pieces.
Shut power off to stove, by turning off breaker. Using a screw driver, removed the 2 screws securing broken bake element to back of oven wall. Grasp the 2 wires holding the prones & gentley removed broken element. Attached new bake element to wires, put screws back in & secured to oven wall, turned breaker to stove back on. Oven works great, had pizza for dinner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Villa Grove, IL
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven heating element needed to be replaced after failure
I had previously removed the element so I began by installing the new element. The wire connectors, did not fit as tightly as they did on the old element due to a slightly different shape on the element. Therefore, I had to take some needle-nosed pliers in order to bend the oven's wire connectors and make them fit tighter. Once that was done I struggled a bit to slip the connectors onto the new element but finally got them on.
There is also a 208V element available for this oven but after calling the web site's phone number was advised that the 208v is for an apartment-type oven and that the 240V is appropriate.
Everything works well!
There is also a 208V element available for this oven but after calling the web site's phone number was advised that the 208v is for an apartment-type oven and that the 240V is appropriate.
Everything works well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn R. from Cambridge, ME
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven heating element had a bright spot in it and I was afraid it would blow while I was cooking.
My husband said HE JUST TOOK OUT A COUPLE OF SCREWS ,TOOK THE OLD ONE OUT AND PUT THE NEW ONE IN .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Ticonderoga, NY
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Baking element burned out
I removed the screws that hold the element in place .
Pulled the element out enough to disconnect the two wires . I then connected the new wires and pushed in the element . I finished off by screwing the bolts back in place.. Voila!!!!!!! I was in business once more!
The part arrived within 48 hours and was very reasonably priced
Pulled the element out enough to disconnect the two wires . I then connected the new wires and pushed in the element . I finished off by screwing the bolts back in place.. Voila!!!!!!! I was in business once more!
The part arrived within 48 hours and was very reasonably priced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Valley, AL
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven bake unit burned out several years ago
Replaced for a friend who was financially unable to purchase the unit. Turned off power to stove. Removed two screws. Inserted the unit and replaced the two screws. All fixed in about 15 min. Now she can enjoy baking again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Spencer, MA
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
3 inch segment of element separated from the whole element
Shut off circuit breaker to stove. Removed oven racks from oven. Removed two phillips head screws located at the base of the bake element at the back of the oven. Gently pull the element toward the front of the oven until the wiring connected to the element by spade connections can be reached. I used a pair of pliers to help separate the element from the wiring. Removed disfunctional element from oven. Sweep out the bottom of the stove with a dustpan & brush. Lay the new replacement element on the bottom of the oven. Connect element to wiring via spade connectors. Gently feed the wires back thru the holes until the the tips of the element follow thru the wire holes until the base of the element is flat against the back of the oven. Screw in screws thru the base to the back of oven - tighten tight. Reset cir brkr. Test oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hal from Brandywine, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element did not work.
I ordered part from Part Select, which literally arrived in 2 days. I unscrewed the two (2) screws holding the old bake element in the oven. Pulled out the element and detached the wires connected to the element, which was easily done without any tools. Attached those wires (again easily by hand with no tools) to the new bake element and screwed the two (2) screws back in. The whole process including ordering the part online, unpacking the box and installing took 15 minutes. Wonderful and in time for my wife and daughter to bake Christmas cookies!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenton from Seattle, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat
I unplugged the stove/oven then unscrewed the bottom element (two screws in the back). I pulled the two electrical clips off the old bake element then removed it. I pushed the electrical clips on the new back element then screwed it back in. After plugging the oven back in and turning it on the oven worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vernon from morehead, KY
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
bottom oven element burnt out
i removed the back cover unpluged 2 wires
inside the oven removed 2 screws from the element . reversed the process to re install the new part
inside the oven removed 2 screws from the element . reversed the process to re install the new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from lexington, OH
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
low heat bottom element had cracked
simply removed screws & old part.., replcd new part & screwed back into place.
Was this instruction helpful to you?
Thank you for voting!