YKERS807SS01 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- benjamin from conway, SC
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out oven bulb
unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce A. from Adena, OH
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element went bad would not heat
Removed screws that hold element remove wires from old element replace with new one replace screws turn power back on at breaker box done.PS make a steak done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Spring, TX
- Parts Used:
- W10155557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
While trying to tighten the oven door handle, the outside glass shattered.
I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MOSINEE, WI
- Parts Used:
- W10823692
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Duel Burner , Inside Burner Out
Removed burned out burner, replaced new burner tested works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Ashburn, VA
- Parts Used:
- WPW10155633
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When removing the warming drawer I did not read the instructions and broke the slide for the drawer. I removed the drawer without pressing the tabs which broke the right slide.
I removed the broken slide by removing 1 screw on the front slide and the back of the slide came out of the slot in the very back (no screws). I fitted the back of the slide into the slot and then replaced the screw on the front of slide. Extended the slides then I pressed the tabs on the drawer and replaced in onto the slides (left and right) . Closed drawer and finished! Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Christoval, TX
- Parts Used:
- W10823692
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dual element burned out
A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.
Was this instruction helpful to you?
Thank you for voting!
replace two stove top burners
It was very easy. Disconnect the electricity. Take the two screws out that hold the top in place. Raise the top and with the pliers change all the electrical connections and retaining bars. Install the two new burned tops. Lower the top and re-install the two retaining screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from West Orange, NJ
- Parts Used:
- WP9760579
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
worn out hinges
Tried reusing old door hinges after removing door to access temp sensor and broke the oven glass twice.with new hinges , new glass went in easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from king city, OR
- Parts Used:
- WP9759242
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replace thermo fuse
turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.
Was this instruction helpful to you?
Thank you for voting!