KFEG500EWH0 KitchenAid Range - Instructions

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

Repair has not been made yet still waiting for the part. The part is on order and was told it would be shipped in 1/3 business days. Still waiting for the part to come from China. This is the problem with parts being made out side the U. S. A.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Removed back cover on range, removed two wires attached to element, then removed element by taking three screws out holding it in place. Installed new element in reverse order of removal. Only problem was relay on control panel board was sticking, and had to tap on it with screwdriver to finally get the oven to preheat.

Turned the breaker off. Removed the racks, pulled the oven out and removed the back. Disconnected and unscrewed the old sensor from the back, connected and screwed in the new one. Returned the racks and slid the oven back in.

The only remotely challenging part was disconnecting the old sensor. I had to figure out where to press with the flat screwdriver to get it to release.

I had found a good YouTube video and didn't use the app.

Shut beaker off
Unhooked wires on element back of stove
Removed all racks
Unscrewed lower plate cover
Removed element
Inserted new element
Rebooked wires to element
Reinstalled cover plate
Turned breaker back on
Turned range on and let heat up
Turned it off
Reinstalled racks

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

I read the help section and it said that the element was likely to be the problem (84%) and the fuse had a 14% chance to be the problem so I purchased both. After watching the video I tried the element first and that's what it was so I returned the fuse, Thanks for the help and video.

The company said it would cost me $698 to repair. I had a 2 year warranty and that was 2 months out of date.

Again thanks for the help.

I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.

Followed the video on this site.

There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Watched the video and realized this was something I could do myself...bear in mind I'm not exactly a handyman! Took me about 30min as the oven also needed some cleaning...my tenant definitely needs to use the self-cleaning!

I have to note, although the heating element was covered by Maytag's 10yr limited parts warranty, I decided to purchase from PartSelect since Maytag could not provide a ship date and I couldn't keep my tenant waiting! Supposedly Maytag had the part in stock but their warehouse was behind because of the pandemic...what a lame excuse! Almost a month later, Maytag has yet to ship the part! Needless to say, am very disappointed in Maytag's after sales and warranty program! I get the impression, they just wanted to pressure me to buy the new part!

Lastly, was very pleased and impressed by PartSelect's customer service! Their website was very easy to use, less expensive than buying direct from Maytag and the part was shipped same day! Thank you PartSelect!

Wanted third oven rack. No problem.