KESK901SBL02 KitchenAid Range - Instructions

Removed old fan by removing all screws except the back two lower screws - here I cut the flange on the old fan to remove. Drilled the back two bottom holes so as to fit over existing screws then replaced the top 3 and bottom 2 screws as well as power leads. Offset screwdriver is a must.

I used the digital multimeter for measure the voltage in the burner and in the digital part,I saw the electric cables

First I turned off the power. Next I disconnected the downdraft vent. Then I removed the cooktop knobs and turned it upside down on the counter. I then removed about 12 screws to remove the element housing. I then unsnapped the old element, disconnected the 3 wires, replaced it with the new element, replaced the housing and screws. I replaced the cooktop, reconnected the downdraft hose and turned on the power.

We removed 4 screws that let us raise the top of the stove. It was then very easy for my husband to remove the old burner and replace the new one. By ordering this part from you and installing it ourselves, we saved $248 from the quote we received from our "Maytag Repairman". Can't beat a deal like this and it was so easy.

received the part sooner than expected, all of the holes lined up, for being the first time working on a stove it could not have gone any better

Moved Oven from wall, removed eight screws holding down the Burner Top. Lifted Top and held it up to remove two screws on the side of the element. Disconnected four wires, replaced element, connected the four wires again and assembled in reverse mode of dissasembly. All went pretty simple, moving oven from wall and adjusting/level it back in place was the most time consuming.
Part works fine, delivery was faster than expected during the Holidays. Good Job Thanks!!!
HAPPY NEWYEAR!!!!

Unplug appliance first. Remove rear cover plate (only to disconnect burner plug). Remove plastic upper side covers. Open oven door & remove two screws holding burner top. Lift off entire top, flip upside down and change element.

We looked online for instructions, not sure how to "lift" the glass top.... There were 2 screws/hex head at the front of the range under the top that when removed allowed the top to be lifted up ..... the elements are on the underside, and with the removal of a few screws and unplugging the element connections (real easy) the burned out element was easily removed and the new one replaced... Less than 15 minutes for the whole operation...HOW COOL!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed the three screws holding on the back plate and removed plate.

Popped out the switch and used the pliers to pull off the wires. Connected the wires to the new switch.

Popped out the broken light. Slid the new lens into the front panel. Slid the light housing onto the new lens.

Re-attached the back plate.

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.

Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.

Removed top of stove replaced heating element ,piece of cake.

Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.