KDRP462LSS0 KitchenAid Range - Instructions

Had to screw off old terminal block & screw on new one

After a couple hours of frustration, I finally called the repair man and had it fixed properly. All the instructions I got from the the various websites didn't really address my model. Just getting the door off the over (with my type of lock) was a challenge. It is really important to have the proper tools for this job and I didn't have them. Live and learn.

As I did not have a manual, I found all the website instructions very helpful. I had quite a hard time after installing the glass to figure out how to put it back together. The insulation between the oven glass is tricky to keep in tact. I also did not have allen wrenches to keep hinges open, so I used a variety of large bolts and screws. Finally after lots of hours, and almost calling a repairman, I did do it!

Tried reusing old door hinges after removing door to access temp sensor and broke the oven glass twice.with new hinges , new glass went in easily.

Order a thermostat and put it on and now it works. Took less than a half hour to repair. Very satisfied and probably saved myself over $200 if a repair man had done it.

We unplugged the range and shut off the cable switch. We took off the back panels and found the thermostat behind the bottom panel. I believe my husband had to take the top panel off first in order to get the bottom panel off. We pulled out the two wires that were connected to the thermostat and then took out the thermostat by unscrewing two screws. We installed the new thermostat (two screws) for our model range, re-connected the two wires, plugged it back into the wall and switched on the cable. We were elated when the panel board lid up and seconds later the oven door opened. It works beautifully. Thank you, thank you, Thank you PartSelect and to everyone that wrote their installation instructions that inspired me to try it. It was very easy and we saved hundreds of dollars.

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy

Pulled out stove from wall..removed all silver screws that hold range back splash. Removed all black robertson screws that hold back panel...removed thermol fuse..2 wires and a blue fac on fuse. Hooked the 2 wires together to temp use oven. Got fuse from parts select and installed...easy easy easy....never will use self cleaning agai..

After describing my problem read the review from other people with a same problem. I can't believe it was so easy not mention how much money I saved. It was the thermostat just needed a screw driver to open about dozen screws from the back panel there it was it was thermostat my 12 years old son just unscrew the two screw and pull tthe pin from both side replaced it with a new one and turn the electric on and there it was every thing is back to normal. My son now has the bragging writes for doing this.

The Kitchenaid oven has 2 interior oven lights. They are behind rectangular glass panels, in an assembly housing The repair is pretty simple. Shut off the power at the breaker box to the oven first. First remove the small screw that holds in the assembly with a Phillips screwdriver. Put down a white piece of paper towel to catch it in case it drops. It is grey color and hard to find against the bottom of the oven. This will free up the assembly and you can move it out. There is a wire on the back so it only comes out a short distance. Next the glass panel covering the bulb must be removed. The small metal clamp with 2 projections that act like a spring to put tension on the glass. Gently pull this out parallel to to the glass and it will release the lens. The old bulb is a simple 2 prong halogen that pulls out easily. Replace it with the new bulb carefully pushing the prongs in. If you did not turn off the power the light will come on immediately. it will get hot quickly so don't touch it for more than a few seconds. Next slide the glass lens back into place into the back of the assembly. Slip the other clip with the screw back on the front. Replace the assembly back into the oven side opening. Secure by replacing the small screw removed in the beginning. You are done. It is about a 5 minute job start to finish. I would replace both bulbs even if only one went out because the other one probably will go out a short time later and you will have to go through this again soon. Oh, and cheap bulbs are not worth it. They are very dim and burn out quickly. Go with the better bulbs you get from PartSelect.

pull out the stove,took the top back panel off, take off wires one at a time on new spark module.. easy

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Repair was super simple . Any one could have done it.

Took off the covers and replaced the little bulbs. Took a long time to figure out how to get the covers off. Bulbs were $26 apiece!

took out door hinges, slightly close door, lift upwards, remove clips on bottom of door, remove screws from 2 inner layers of glass, insert new glass, perform revers order reassembly..cleaned all inner glass, and surrounding parts prior to reassembly