KGST300BWH0 KitchenAid Range - Instructions

Looked online and found it was probably the igniter which wasn't firing. An incredibly gratifying and easy experience with the self-fix. Worked on the first try just like new.

Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.

I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Replaced both rollers....Quick and Easy!!

The stove burners and oven broiler worked fine so it was obviously something with the oven ignition. My oven is 14 years old so it made sense that the ignition would wear out. I followed the instructions provided on the PartSelect website for this repair and it worked perfectly. Very easy fix!

Replacing the igniter took care of the problem. I just wish I had made better notes about how the wire were routed. It would have saved time as I re-assembled everything. Th ejob itself was really easy.

Replacing an oven igniter is one of the easiest repairs you can make to your oven. There are two igniters - one for the broiler and one for the oven itself. Oven Igniter: Start by removing the rear panel of the oven which attaches with a couple screws. Inside the oven, remove the "butterfly" shaped heat deflector (over the flame tube) which attaches with four screws. You now have access to the igniter. Remove the two screws which attach it to the bracket. On the rear of the oven, unplug the two spade connectors. Pull the igniter out from the front of the oven. Fish the wires for the new igniter through the same hole. Plug the 2 new wires back in. You can't mess this up - the wires have matching connectors and you can't get them confused. The broiler igniter is a little more complicated. You will have to remove the side panel of the oven to reach one of the connectors. It's just a couple more screws. The procedure is the same, but the wires are much harder to "fish" through the hole though. Unscrew the broiler igniter from the bracket and unplug the wires. Before you pull them out, attach a length of clothes hanger so that you pull the hanger into the oven from the rear. This way you can attach the new wires to the hanger and then pull them through to the back of the oven. If you don't attach something when you pull the old wires out, it is very hard to fish the wires for the broiler igniter to the rear of the oven. Good Luck!

Remove the bottom panel and confirmed that the igniter was not lighting. Unsrcrew the igniter from the housing in the oven, then removed the back of the range and unplugged two leads from their conections and ran the wires through the insulated back wall of the oven. To replace the part just did the opposite of above. Piece of Cake. Want to say also that I was astounded at the speed in which I received my part. Ordered it at 3:30 PM on Friday afternoon and received it by 10 AM Saturday. And with standard delivery! Thanks!

Pulled insulation out of the way to feed wires through. Might have helped to tie pull string to old wires but fishing them through was not to difficult.No need to cut wires; it is not a good idea to make unnecessary splices.

I very simply replaced the gasket where it belonged and I was good to go!

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

I removed the door and I took it completely apart in order to replace the broken inner glass pieces. The door has about 30 separate pieces, so it is a meticulous repair and I recommend that you be fairly handy if you are going to attempt this. Something that seems as though it should be pretty simple took me nearly two hours to complete. I am happy to report that the result was a resounding success. The broken oven door glass had been affecting the oven temperature and as the result the baked foods were adversely affected. Cakes, pies, etc, would either be over or under cooked with no way to properly regulate the temperature. The inner glass is necessary in order to maintain correct oven function, so replacing it made everything work as designed once again.