KERC507EAL4 KitchenAid Range - Instructions

The repair was simple:
PartSelect always seems to have the parts you need and they get them to you quickly.
Baking element - I removed the two screws that hold the element to the back of the oven ( Philips head). Disconnected the spade type electrical connections from each end of the element. Note: use some type of clamp to hold the wires from pulling back into the outer section of the oven. I used wooden clothespins). Reverse the process to install new element.
Broiler element - I placed the shipping container over the new baking element to protect it. Then removed the four screws holding the top element to the back of the oven ( Philips head). Take care to mark the 4 wires for the broiler element. ( 2 for outer coil & 2 for inner coil) Clamp these wires also after disconnecting. Slide the 2 "L" shaped hangers out of there slots. When installing the new element connect the wires first then slide the "L" shaped hangers back into the slots. reinstall the 4 screws and your done. I did the repair with out removing the oven door ( ours is difficult to get back on ) with the door off the job will take less time and access will be easier.

Had to screw off old terminal block & screw on new one

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would require me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.

It was difficult to reach the back of the oven inside to remove screws. I had to use an extended socket with a bit tip. When I tried to remove the element from the clips, the clips slid back inside the insulation at the back of the oven. I had to take the back panel off of the oven, push the clips through the opening and then I used a bag clip to hold them so they would not slide back into the opening. I could not lift the door off-too heavy- to get closer to the back of the oven to put the clips and screws back on so I laid the oven on its back after putting the back cover on. The oven door was so heavy then that I had to prop the oven door open with my 24 inch rolling pin. I then leaned down into the oven and managed to get the clips and the screws back in. I then put the oven upright again, plugged it in, then had to re-level the whole thing. I turned it on and it worked. This probably would have been easier if I were not 65 years old and had some help. I was not giving up though. I got it done.

Turned off electricity at breaker, slid stove out from wall. Disconnected unit. Removed back panel (4screws). Disconnected double broiler wires from the back. Unscrewed element bracket from back wall of oven (2 screws). Removed and replaced element and replaced screws to back wall of oven. Reconnected wires on the back of the oven where element connectors protrude from oven wall. Replaced back panel (4 screws). Removed oven door by pulling forward (no screws involved). Removed screws from bottom of door holding trim on (7 screws). Removed bottom trim and side trim. Removed front glass. Removed inner portion of door (it's just stacked together sandwiching some insulation). Removed track holding 2 glass panels (6 screws and pressure brackets). Removed one screw from corner of track. Removed and replaced inner glass. Lay door flat on floor front down to reassemble. Place glass insulation (looks like rope) around window opening. Lay the track containing he replaced glass down (side with most shallow recess). Replace 6 screws and pressure brackets. Replace large insulation and inner door panel. Reinstall front glass in slots under door handle. Replace oven door back. Reinstall side and bottom trim in reverse order to removal. Replace 7 screws along bottom of door. Reinstall door assembly to oven by sliding tabs back into the range. Done!

Removed the element by using a basic screw driver...two screws. Detached the slip on wire attachments (don't know what they are called). Re-attached new element and screws. Very simple. I was hoping elements were a little cheaper, but I was impressed with the speed that Part Select delivered my new element. I'll use them again.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Turned breaker off. Removed oven door for access, two screws loosened element, unplugged wires from element & removed element. Reverse order to install. Perfect fit. Thanks.

Replaced both rollers....Quick and Easy!!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.

Remove two screws. Plug n play.

TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.

We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.

Had difficulty removing the two screws holding element(range is eighteen years old.Screws were badly rusted)After that,it was a piece of cake