KERC607HBS0 KitchenAid Range - Instructions

I think this does not qualify as a repair. I called and ordered the oven rack, it came in the mail and I put it in the oven. Nothing to it.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Pulled the oven door out. Took the whole door apart and put it back together. The first time I put it back together the inner glass was still loose so I had to take it apart again and figure out how to hold everything together tightly. Your part was perfect. The glass was exactly the same as two others in the oven door. I wish I had instructions but when the parts fit it sure helps.

looked on internet on how to remove top. an easy fix after watching video

The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.

Had to remove side panel then very easy

Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.

took the door off, removed the screws, removed the back of the door, took the broken glass out, put new glass in, reassemble door, put door back on.

First BE SURE TO TURN OFF THE CIRCUIT BREAKER!!! Remove the oven door if you need to get closer to the work. Then remove the screws securing the the element to the the oven. There were two on each side in the back where the element goes they the wall and two more that held the element to the upper surface. Carefully pull the element out to gain access to the wires and terminals. Gently pull each wire off one at a time, being sure not to allow the wire to get pulled back into the rear part of the oven. Reconnect each wire securely to the new element. Doubly check each connection! Then replace each screw and you should be set!

The new element wiring placements were totally different from the old element. Lucky for me the lettering printed on the terminals for each pole was the same as on the old one. It was just a matter of matching up each terminal pole lettering. The instructions that came with the new element were of no help at all. Youtube was my best helper.

removed side and back strips after pulling out stove, removed top glass , installed new insulating tape around edges fitted new top on stove and replaced trim strips.

This worked very well, thanks to the advice posted from other users. The only part that was a bit unclear was removing the door. There are small, slotted metal pieces screwed into the sides of the oven to hold the door hinges in the slots. After removing those, I had to hold the door and push it up and down, and a little bit side to side, to get the hinges to start sliding out, but they did. There are no other screws or brackets holding them in place. The hinges are on springs, so they do snap up when they come out of the slots in the sides of the oven. But they only snap to a 90 degree angle, so they won't cut your fingers off. You'd have to hold your fingers right on them to even get pinched. After that, I just kept taking screws out of the door until I got through to the back panel, replaced it, and put it all back together.

removed door from range and slowly took apart until reached inner glass. there are three pcs of glass, front and two inner. was able to clean the inside which was dirty after 15 years of use. took alittle over an hour from start to finish including thorough cleaning.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

There are already good instructions here on doing the repair, so I will just add what I found important. 1) using penetrating oil and an impact wrench on the screws that hold the inner glass to the inside of the oven door - they were rusted tight. 2) the outside glass front sits on the front of the door, on top of the edges of the side pieces, even though it looked to me like the side pieces were meant to go over the edges of the glass - they aren't. The bare side edges of the glass aren't covered with any trim at all. The video on removing the oven door that matched the kind of hinges I had showed taking them off the door as part of disassembly of the door. I didn't find that necessary at all, and you probably won't either. Less parts to have to get back in place. The hard part to me was finding the correct disassembly video to match the oddball hinges, which isn't to say it's a bad design - actually it seems better that the other more common designs. Take out the two screws above where the hinges enter the range, and lift the door up, away from the range, and off. Easy peasy.