KESC308LSS0 KitchenAid Range - Instructions

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

received the part sooner than expected, all of the holes lined up, for being the first time working on a stove it could not have gone any better

Moved Oven from wall, removed eight screws holding down the Burner Top. Lifted Top and held it up to remove two screws on the side of the element. Disconnected four wires, replaced element, connected the four wires again and assembled in reverse mode of dissasembly. All went pretty simple, moving oven from wall and adjusting/level it back in place was the most time consuming.
Part works fine, delivery was faster than expected during the Holidays. Good Job Thanks!!!
HAPPY NEWYEAR!!!!

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

I refered to what I had read on repair stories of broken glass...then went to fixing mine and before I new it I was done and glass replaced...it was very easy as long as you watch what you are doing when u take it apart and replace things the same as they were removed......thank you

Unplug appliance first. Remove rear cover plate (only to disconnect burner plug). Remove plastic upper side covers. Open oven door & remove two screws holding burner top. Lift off entire top, flip upside down and change element.

We looked online for instructions, not sure how to "lift" the glass top.... There were 2 screws/hex head at the front of the range under the top that when removed allowed the top to be lifted up ..... the elements are on the underside, and with the removal of a few screws and unplugging the element connections (real easy) the burned out element was easily removed and the new one replaced... Less than 15 minutes for the whole operation...HOW COOL!

We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

Pulled the oven out from the counters and unplugged the electrical cord. Unscrewed the three screws holding the center back panel on and removed the panel. Located the temperature probe in the upper left part of the oven and followed the wiring to where it was connected. Unconnected the wire from the connector. Removed the screw holding the probe and pulled it out from the oven. Put the new part on and screwed it to the oven. Connected the wiring to the connector. Put the panel into the holding brackets and screwed in the three screws. Plugged in the oven and put it back against the wall. Turned on the oven, set a temperature and watched to see if it stopped at the set temperature. Bake3d dinner and ate it.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

Removed burned out burner, replaced new burner tested works fine

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.