KGST300FWH1 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rustin from LARAMIE, WY
- Parts Used:
- WP8053344
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
FAULT CODE F-3
REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from LATON, CA
- Parts Used:
- 814323
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate pads that protect the range top had worn and were flat.
It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.
Was this instruction helpful to you?
Thank you for voting!
Clearly, the bulb was the problem. The gasket is an invitation to more trouble.
Simple. But beware changing just the bulb when the gasket is not secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from SHOREVIEW, MN
- Parts Used:
- WP9781049
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
left cover for the oven light broke when trying to replace the bulb
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from LIMINGTON, ME
- Parts Used:
- WP9781049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
oven light glass cover was broken
took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from PARMA, OH
- Parts Used:
- WP9782033
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
hinge would pop out each time the door was closed.
With glass side down:
1. Removed the side panels
2. Removed the bottom panel
Turned over door holding glass in place.
3. Removed outer glass panel
4. Removed handle top
5. Removed top screw holding hinge mechanism
6. Removed screw for spacer and clip holding hinge mechanism
7. Lifted hinge mechanism out and replaced with new part.
Reattached parts and screws in reverse order (6-1)
1. Removed the side panels
2. Removed the bottom panel
Turned over door holding glass in place.
3. Removed outer glass panel
4. Removed handle top
5. Removed top screw holding hinge mechanism
6. Removed screw for spacer and clip holding hinge mechanism
7. Lifted hinge mechanism out and replaced with new part.
Reattached parts and screws in reverse order (6-1)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from LAKEWOOD, CO
- Parts Used:
- WP4454392
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
spark module failure, wouldn't spark.
The repair was fairly straightforward, much easier the second time around. The first part was defective. (irregular spark). I reordered and installed the new one. It works, but nowhere near as good as the original.The problem is that the frequency of the spark on these replacement modules is only once per second. To get technical, the gas as presented to the spark is turbulent, causing several sparks to occur before the ideal mixture coincides with the spark. Needless to say, there is an excess of gas wafting around the kitchen until it lights, sometimes in excess of 20 seconds. NOT SAFE! Our BBQ and fireplace insert spark orders of magnitude faster than this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Thousand Oaks, CA
- Parts Used:
- WP9782033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Both left and right door hinges broke off their pins
The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly J from KAPLAN, LA
- Parts Used:
- WP3185804
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
igniter on top right front burner was shorting out,it would click but not ignite burner
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christie from Provo, UT
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
grate pads were gone, making cleaning difficult
Put the new pad in and it was done. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from PUTNAM VALLEY, NY
- Parts Used:
- WP8053344
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was overheating and locking the door. Codes indicated the temperature sensor could be the issue.
Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from MILWAUKEE, WI
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Storage drawer would not completely open.
Replaced damaged drawer roller: easy peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from COVINGTON, GA
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove got way too hot
Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes
Was this instruction helpful to you?
Thank you for voting!