KESC300HWH6 KitchenAid Range - Instructions

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Moved Oven from wall, removed eight screws holding down the Burner Top. Lifted Top and held it up to remove two screws on the side of the element. Disconnected four wires, replaced element, connected the four wires again and assembled in reverse mode of dissasembly. All went pretty simple, moving oven from wall and adjusting/level it back in place was the most time consuming.
Part works fine, delivery was faster than expected during the Holidays. Good Job Thanks!!!
HAPPY NEWYEAR!!!!

I refered to what I had read on repair stories of broken glass...then went to fixing mine and before I new it I was done and glass replaced...it was very easy as long as you watch what you are doing when u take it apart and replace things the same as they were removed......thank you

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Unplug appliance first. Remove rear cover plate (only to disconnect burner plug). Remove plastic upper side covers. Open oven door & remove two screws holding burner top. Lift off entire top, flip upside down and change element.

We looked online for instructions, not sure how to "lift" the glass top.... There were 2 screws/hex head at the front of the range under the top that when removed allowed the top to be lifted up ..... the elements are on the underside, and with the removal of a few screws and unplugging the element connections (real easy) the burned out element was easily removed and the new one replaced... Less than 15 minutes for the whole operation...HOW COOL!

We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.

Removed the element by using a basic screw driver...two screws. Detached the slip on wire attachments (don't know what they are called). Re-attached new element and screws. Very simple. I was hoping elements were a little cheaper, but I was impressed with the speed that Part Select delivered my new element. I'll use them again.

looked it up on line how to change it. before I ordered part, to see how much of a job it was. was real simple to change, had no problem. also part select sent the correct part. Job went well

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

2 screws,coule plugs,test_OK.Fully functional for days now. Thank you !

This job replacing the was so easy, it took about ten min,to do it thanks

Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.