KGRT600HBL5 KitchenAid Range - Instructions

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

Had to screw off old terminal block & screw on new one

As a relatively handy person, I have built homes, and done every kind of repair you could imagine from plumbing to heavy construction. I never wanted to play with appliances, just couldn't read those diagrams well enough to feel comfortable. Parts select has changed my life and saved me so much money and I have repaired appliances in several of the homes with no issues using your videos and parts as my guide.

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

Pulled insulation out of the way to feed wires through. Might have helped to tie pull string to old wires but fishing them through was not to difficult.No need to cut wires; it is not a good idea to make unnecessary splices.

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

Most of the basics have been covered in previous post. I can add this- those who claim 15 minute-fixes are delusional, unless they're appliance repairmen. Secondly- what will take time is the cleaning. If you have to do this repair, which requires extensive disassembly of the door, it would be foolish not to take advantage of the opportunity to thoroughly clean all four layers of glass. Take the glass panes outside and use oven cleaner. This takes time. Other than that, the pancakeing of the components on re-assembly is tricky, but you can do it. Don

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the glass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!

Per the instructions listed in your customer replies

Replaced valve, 3 pipe connections 4 wire connections, still did not work, small flip up valve was set at off position, set to on, still did not work, replaced ignitor, bingo that was the real problem, reinstalled old valve, still working fine; returned new valve assembly for full refund! Thank You

Take 4 screws off to remove oven pan, once pan is off , you can see the igniter. Take off two screws and remove old igniter. Be sure to run wires on new igniter where they were on the old igniter.

Pulled the oven out from the counters and unplugged the electrical cord. Unscrewed the three screws holding the center back panel on and removed the panel. Located the temperature probe in the upper left part of the oven and followed the wiring to where it was connected. Unconnected the wire from the connector. Removed the screw holding the probe and pulled it out from the oven. Put the new part on and screwed it to the oven. Connected the wiring to the connector. Put the panel into the holding brackets and screwed in the three screws. Plugged in the oven and put it back against the wall. Turned on the oven, set a temperature and watched to see if it stopped at the set temperature. Bake3d dinner and ate it.

Replaced both rollers....Quick and Easy!!

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover