KERC500HBT0 KitchenAid Range - Instructions

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the glass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!

That should have been an easy repair according to previous responders that replaced this part.

The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.

The second issue was I could not pull the connector through the hole where the sensor wires pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.

NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.

Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!

After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

Most of the basics have been covered in previous post. I can add this- those who claim 15 minute-fixes are delusional, unless they're appliance repairmen. Secondly- what will take time is the cleaning. If you have to do this repair, which requires extensive disassembly of the door, it would be foolish not to take advantage of the opportunity to thoroughly clean all four layers of glass. Take the glass panes outside and use oven cleaner. This takes time. Other than that, the pancakeing of the components on re-assembly is tricky, but you can do it. Don

Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.

It was very easy. Disconnect the electricity. Take the two screws out that hold the top in place. Raise the top and with the pliers change all the electrical connections and retaining bars. Install the two new burned tops. Lower the top and re-install the two retaining screws.

I can't believe how easy this was to fix. 1. Unplug the stove. 2. remove the screws that hold the stove top in place. 3. pull the top up, unplug the electrical wires and unscrew the ground wire 4. remove the stove top and flip it over. 4. unscrew braces holding the burners in place. 5. with pliers, remove the wire connections between stove top and old burners 6. replace with new burners. 7. reattach everything. And you're done! Go brag to the neighbors about what you just did.

My wife was complaining about poor baking results with the oven in the home we just purchased, so I hooked up my digital temperature meter and found it was almost 50 degrees of, so I tried the ovens off set program to bring it closer into range. That did the trick ,but she complained about poor baking still. I watched the oven cycle about 8 times and saw her problem. The oven was inconsistent when dropping below set temps, some times it was 20 degrees off, other times it was 80+ degrees off before the element kicked back on. I started with the sensor, it came with easy instructions including wire hi temperature wire nuts if the connectors didn't match... which they didn't. It was very easy to access the senor for replacement. Just unscrew about 10 screws, pull the back access panel off and there it is. Cut the connectors on both ends making sure to leave plenty of wire on each end. Wire nut them together and reinstall the back panel. Reset the oven off set back to zero and check the oven temp watching about 6 cycles. Comes right on now, and her first baking effort came out great...I am pretty sure that was the problem.

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

Removed burned out burner, replaced new burner tested works fine

Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws inside oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.

Removed the door. Took out all the screws. Removed the glass that was cracked. Put in the new piece. Put the screws back in place. Put the door back on and it was a done deal.

Removed top of stove replaced heating element ,piece of cake.