YKGST307HB4 KitchenAid Range - Instructions

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

Followed Mfgs instructions.

I did the repair following your instructions and it went very well. Now the temperature is working good , but the oven is heating up very slow. So now what should I do to fix the oven?

Replacing the igniter took care of the problem. I just wish I had made better notes about how the wire were routed. It would have saved time as I re-assembled everything. Th ejob itself was really easy.

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr

Followed instruction on web site

My wife was complaining about poor baking results with the oven in the home we just purchased, so I hooked up my digital temperature meter and found it was almost 50 degrees of, so I tried the ovens off set program to bring it closer into range. That did the trick ,but she complained about poor baking still. I watched the oven cycle about 8 times and saw her problem. The oven was inconsistent when dropping below set temps, some times it was 20 degrees off, other times it was 80+ degrees off before the element kicked back on. I started with the sensor, it came with easy instructions including wire hi temperature wire nuts if the connectors didn't match... which they didn't. It was very easy to access the senor for replacement. Just unscrew about 10 screws, pull the back access panel off and there it is. Cut the connectors on both ends making sure to leave plenty of wire on each end. Wire nut them together and reinstall the back panel. Reset the oven off set back to zero and check the oven temp watching about 6 cycles. Comes right on now, and her first baking effort came out great...I am pretty sure that was the problem.

The stove burners and oven broiler worked fine so it was obviously something with the oven ignition. My oven is 14 years old so it made sense that the ignition would wear out. I followed the instructions provided on the PartSelect website for this repair and it worked perfectly. Very easy fix!

Very easy, just a phillips-head screw driver. Part shipped quickly, great help on the phone from a PartSelect rep, confirming the part!

Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.

Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.

The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.