KERS807SBL04 KitchenAid Range - Instructions

Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.

Using the video from PartSelect I followed the steps shown. Sliding the range out was difficult so I tilted it forward resting the frame on a 5 gallon plastic bucket. I did have to crimp on a new terminal. The repair was straightforward.

I was stopped by the third screw on the roof of the oven, which was slightly rusted and would not budge in spite of using WD40! I had to enlist the aid of my son who arrived with better tools, including a SQUARE phillips head socket set. He also had to spend some time pinching and slightly reconfiguring one of the attachments in the back which did not slide together naturally. So, for an 82 year old retired housewife this was not as simple as it looked, but it was a piece of cake for guys like Erik with the know-how and the proper tools!

Turned off circuit breaker to oven
Removed oven door
Removed screws of reflector plate and top and back of oven
Gently pulled element out and down slightly
Removed slide crimps on wires
Replaced reflector plate on new element
Connected slide crimps on wires
Screwed reflector plate with new element to top and back of oven
Done. Total time 22 minutes
Tested and it’s perfect!

removed the top cap which held the control board - unplugged the old one & plugged in the new one - worked perfectly- had to be careful as the new one was plugged in & attached with 2 screws

Turned the breaker off to the stove.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

good, used tie wire with a hooked end to fish one wire out of the back, to keep from removing the oven

unscrew cover
remove old bulb
screw in new bulb
replace cover

Removed old fan by removing all screws except the back two lower screws - here I cut the flange on the old fan to remove. Drilled the back two bottom holes so as to fit over existing screws then replaced the top 3 and bottom 2 screws as well as power leads. Offset screwdriver is a must.

Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you