YKGRT607HW5 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from West Sayville, NY
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
storage drawer fell off track, roller wheel replaced
real easy one to take care of, when the drawer broke I thought it was more than what it really was, after looking at it and seeing the wheel was gone I ordered the part and it came very quick, drawer is now fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westminster, CO
- Parts Used:
- WP3184533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fiber Gasket around Pyrex Light Lens was mis-shaped
All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!
Was this instruction helpful to you?
Thank you for voting!
Glass window shattered when touch by cold food
Never repaired an oven before, I just used a screwdriver and went slowly taking this over door apart to replace this glass. I just took piece by piece apart until the glass came out and retraced my steps to install the new glass. Sure glad I did this myself, a new convection oven stove would easily set me back 1,500.00 and......save a bundle on service call fees.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ellen from Altamont, NY
- Parts Used:
- WP9782065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My stove had been taking an increasingly long time to warm up, and then would eventually would not warm up more than 315 degrees.
I researched the problem on the internet, and all of the data led me to believe I had a bad igniter. My husband and I viewed a youtube video about installing a new one, and then I read step by step instructions on another site. We thought we would be able to easily do this ourselves, so we ordered the part from PartSelect, and I received the part within a couple of days. After taking the back off the stove, and the pan off the bottom of the oven, we attached a string and pulled through the old wires, and then attached the new wires on the igniter and pulled them to the back of the stove and connected them. The part was exactly what we needed, and now the stove works like it did when it was brand new! I was very happy with the results! MEF
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heide from Delray Beach, FL
- Parts Used:
- 3150144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
meat probe for the oven needed to be replaced
No repair. I've used the new one and like the one that cracked on the wiring it works beautifully. I APPRECIATED THE VERY QUICK RESPONSE FROM YOU AS I RECEIVED IT IN ONLY 2 DAYS. THANK YOU
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from The Woodlands, TX
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber pads on bottom of grate broke off, grate was scratching stainless steel top
I just put the grate pads in the bottom of the grate. The repair was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Branchburg, NJ
- Parts Used:
- 9782081
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not heat over 250 just err when start
I read it may be the temp sensor. Ordered a new one. Took a minute to undo three screws holding the back on, and one screw for the sensor. But still didn't work. Then realized maybe the oven was changed to Celsius. In manual - open door, hold broil for seconds and changed back to Fahrenheit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Newnan, GA
- Parts Used:
- W10355051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
Baked on sauce
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Warren, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven light would not work--faulty socket
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
Accidently allowed the oven door to close without slowing it down. Result was a fractured inner door glass.
Removed the door just like you would do when cleaning the oven; I placed the door on a blanket on the kitchen table and carefully disassembled the door. There were more parts than I expected so keeping track of where everything went was important. I might add that without the use of my cordless variable speed drill motor removal of some of the screws would have been difficult. Adding the weight of the drill motor with sufficient push power I was able to tap the switch which "snapped" the screw loose. Don't think I could have done it with a hand type screw driver without stripping the head. Knowing your tools is very important.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Bucklin, KS
- Parts Used:
- WP9781049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original oven light lens had cracked and broken in two.
I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from HELENA, OH
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven drawer would not slide...because of worn out nylon roller.............
removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Denver, CO
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing bumper pads
Original bumper pads NOT glued into the burner grates. Hence they began to disappear during routine use and cleaning. Very simple repair with a little glue this time around. But fairly expensive for a very small part set
Was this instruction helpful to you?
Thank you for voting!