KGRK201TSS0 KitchenAid Range - Instructions

Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)

Replace with new one just push it on the shaft!

I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.

The oven was inconsistanty lighting and I could not predict when it would. After reading some repair reviews I determined that the problem was most likely the igniter. I purchased one from your site and it arrived the next day. Awsome! Had to take out six screws to get to the wiring and removed the igniter. The wiring was a simple plug. Replaced the igniter in about 20 minutes and the oven has been working flawless every since. THANKS!

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Thinking we had a difficult/expensive repair, when the oven stopped working this summer - we just took advantage of the weather and grilled out. Apple season and the desire for fresh baked apple pie motivated us to action. We ordered the part - found simply on the site - it arrived promptly. A screw driver took off the oven bottom, we replaced the igniter and within 15 minutes our oven was working again. Why did we wait so long?

Remove the oven door by opening halfway and lifting door away from stove. Removed racks and bottom pan from oven area exposing the gas bar and vertical mount igniter. Next remove bottom storage door. With phillips screwdriver remove 2 screws securing rear cover plate in back of storage area, accessing the igniter connection, and unplug the plug. Next back in oven, remove 2 5/16 sheet metal screws securing igniter with a nut driver and remove igniter by getly pulling disconnected end thru to oven. Now reverse process, install new vertical mount igniter and push connection down thru to storage area, then reconnect wire connection and put cover plate back on.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.

First I removed the bottom plate in the oven. The ignitor was located at the rear of the burner and I removed to screws and it was loose except for the two wires. Next I removed the bottom tray from the stove. Two screws held the metal guard in place at the rear of the stove. After removing the plate, I determined which wires belonged to the ignitor, unplugged them at the coupling and pulled the wires out through the bottom of the oven. Replacing the ignitor was simply to reverse the proceedure. PartSelect got the part right out to me, installing the new part was a breeze, and my wife calls me her "hero." This site was a real help and saved me a service/repair bill. Thanks!
Fred

Unscrewed bottom piece; put on tape and new glass; re-installed bottom.

I turned off the gas at the back of the oven & unpluged it. I then removed the 2 screws that secure the oven bottom plate to the oven. Once removed, that exposes the oven burner & igniter. There are 2 sscrews that secure the igniter to the burner; remove those screws, & pull the igniter wires out, to expose the connector. Unplug the connector, & the igniter is free. Just reverse the process with the new igniter.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, drilled pilot holes and installed wood screws into the floor and rear wall stud.

Remove two screws back panel and remove sensor two screws inside top oven.

Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Plug in the element put the wires back in the hole and screws the element on and that was it. Worked great.