KESS907SSS04 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mansukhlal Dayabhai from Moultrie, GA
- Parts Used:
- W10823698
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Beingold the glass top stuck hard
unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- benjamin from conway, SC
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out oven bulb
unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from ROWLEY, MA
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The inner heating element was not working
The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce A. from Adena, OH
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element went bad would not heat
Removed screws that hold element remove wires from old element replace with new one replace screws turn power back on at breaker box done.PS make a steak done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from CARLTON, TX
- Parts Used:
- WP9760774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element was shorted out and not working.
Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Spring, TX
- Parts Used:
- W10155557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
While trying to tighten the oven door handle, the outside glass shattered.
I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MOSINEE, WI
- Parts Used:
- W10823692
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Duel Burner , Inside Burner Out
Removed burned out burner, replaced new burner tested works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Ashburn, VA
- Parts Used:
- WPW10155633
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When removing the warming drawer I did not read the instructions and broke the slide for the drawer. I removed the drawer without pressing the tabs which broke the right slide.
I removed the broken slide by removing 1 screw on the front slide and the back of the slide came out of the slot in the very back (no screws). I fitted the back of the slide into the slot and then replaced the screw on the front of slide. Extended the slides then I pressed the tabs on the drawer and replaced in onto the slides (left and right) . Closed drawer and finished! Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lacey from Raleigh, NC
- Parts Used:
- W10823692
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
2 burners burned out of flat top stove
I can't believe how easy this was to fix. 1. Unplug the stove. 2. remove the screws that hold the stove top in place. 3. pull the top up, unplug the electrical wires and unscrew the ground wire 4. remove the stove top and flip it over. 4. unscrew braces holding the burners in place. 5. with pliers, remove the wire connections between stove top and old burners 6. replace with new burners. 7. reattach everything. And you're done! Go brag to the neighbors about what you just did.
Was this instruction helpful to you?
Thank you for voting!