KESK901SSS06 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- benjamin from conway, SC
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out oven bulb
unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Kansas City, MO
- Parts Used:
- W10823697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Front Burner Burnt Out
This job replacing the was so easy, it took about ten min,to do it thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Spring, TX
- Parts Used:
- W10155557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
While trying to tighten the oven door handle, the outside glass shattered.
I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Brevard, NC
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burned out heating element for radiant heat burner
I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mansukhlal Dayabhai from Moultrie, GA
- Parts Used:
- W10823698
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Beingold the glass top stuck hard
unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Humansville, MO
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Terminal Block was melted where the cord had came lose.
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from cleveland, TX
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner Would,Nt Heat Up.
Removed top of stove replaced heating element ,piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce A. from Adena, OH
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element went bad would not heat
Removed screws that hold element remove wires from old element replace with new one replace screws turn power back on at breaker box done.PS make a steak done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Fairport, NY
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burner wasn't light up.
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggie from Gresham, OR
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not needed
screwed in the new oven light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Grantsville, UT
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
terminal block back of range shorted and burned
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Brazoria, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Power block terminal failure
Ordered part needed. Much, much cheaper than purching a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Channelview, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
R&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from CARLTON, TX
- Parts Used:
- WP9760774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element was shorted out and not working.
Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Roberts, MT
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wiring Block shorted due to moisture and Stove had no Power
This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.
Was this instruction helpful to you?
Thank you for voting!