KDRU707VSS00 KitchenAid Range - Instructions

I did not remove the door. After removing as much broken glass as possible, I removed the two screws at the bottom of the door, pushing a bit against the plastic oven vents so the screwdriver could fit into the screw heads. I then removed the two screws on top of the oven door. This releases the outside of the door. I then removed the two bottom screws holding the bracket that holds the piece of glass fitting into the slot at the top. I bent back the tabs with pliers, cleaned the last bit of glass out of the slots, and then put the new glass in and bent the tabs back as much as possible. It actually was pretty tight. The rest is just cleaning and putting the pieces back together. Just be careful as the four screws that go into the top and bottom of the door are actually different from the other screws. Just make sure you keep all screws separated and use them as removed. Not too bad, just time consuming.

We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.

Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.

R&r

EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare

Ordered part needed. Much, much cheaper than purching a new range.

This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy

Just wanted an additional roll out oven rack

Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm glad I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.

As I did not have a manual, I found all the website instructions very helpful. I had quite a hard time after installing the glass to figure out how to put it back together. The insulation between the oven glass is tricky to keep in tact. I also did not have allen wrenches to keep hinges open, so I used a variety of large bolts and screws. Finally after lots of hours, and almost calling a repairman, I did do it!

After a couple hours of frustration, I finally called the repair man and had it fixed properly. All the instructions I got from the the various websites didn't really address my model. Just getting the door off the over (with my type of lock) was a challenge. It is really important to have the proper tools for this job and I didn't have them. Live and learn.

took out door hinges, slightly close door, lift upwards, remove clips on bottom of door, remove screws from 2 inner layers of glass, insert new glass, perform revers order reassembly..cleaned all inner glass, and surrounding parts prior to reassembly

Instructions were clear and the work was easy. Take your time and think about what you are doing, and you won't have any problems replacing the glass.

Removed the door from the unit. Set the door face down on a work surface. Remove the screws and put them in a separate place from the rest of the screws (They are a different style of screw). Turn the door back over. Remove the two clips at the bottom on the door. The door front will slide down. Set the door front off to the side with the two clips and the screws. Remove the screws securing the brackets for the next level of glass (Mark which it the top and which is the bottom bracket. Place the glass, brackets and screws together. Remove the next glass/bracket assembly and set it aside with the screws. Lift the inside metal glass retainer and set it aside. Remove the old glass and install the new glass and reverse the order of the disassembly process.