KESK901SBL04 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace two stove top burners
It was very easy. Disconnect the electricity. Take the two screws out that hold the top in place. Raise the top and with the pliers change all the electrical connections and retaining bars. Install the two new burned tops. Lower the top and re-install the two retaining screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from CARLTON, TX
- Parts Used:
- WP9760774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element was shorted out and not working.
Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from West Grove, PA
- Parts Used:
- W10823697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Left front did not work
Open oven door and remove two screews with 5/16 nutdriver to remove hole top of stove.Just lift up gently on front of top and pull toward you and when about 4 inch clearance on back of top you will see where all the wires connect ,press the side tabs of this big connector and it will release very easy to remove the top.Place top on bath towell upside down on countertop and remove 4 screws and 2 clips on the bad burner with the same 5/16 nut driver and remove the three wires and reinstall the same way then reinstall the top on the stove in the same order.Very Easy Job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Brazoria, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Power block terminal failure
Ordered part needed. Much, much cheaper than purching a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from San Antonio, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Contractors on my home did not tighten nuts on terminal block when installing. This caused an arch across terminal burning up unit .
Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm glad I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce A. from Adena, OH
- Parts Used:
- WP9760774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element went bad would not heat
Removed screws that hold element remove wires from old element replace with new one replace screws turn power back on at breaker box done.PS make a steak done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deb from Eastvale, CA
- Parts Used:
- WPW10179152
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven racks
We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Waxhaw, NC
- Parts Used:
- WPW10179152
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Remove racks before self-cleaning
Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggie from Gresham, OR
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not needed
screwed in the new oven light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward J from Baxter, MN
- Parts Used:
- W10823697
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner bad
looked it up on line how to change it. before I ordered part, to see how much of a job it was. was real simple to change, had no problem. also part select sent the correct part. Job went well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Brevard, NC
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burned out heating element for radiant heat burner
I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mansukhlal Dayabhai from Moultrie, GA
- Parts Used:
- W10823698
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Beingold the glass top stuck hard
unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dr PauMari from Alamogordo, NM
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Melted and fused together wires due to non-grounding of terminal block
We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from West Orange, NJ
- Parts Used:
- WP9760579
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
worn out hinges
Tried reusing old door hinges after removing door to access temp sensor and broke the oven glass twice.with new hinges , new glass went in easily.
Was this instruction helpful to you?
Thank you for voting!