KDRU783VSS00 KitchenAid Range - Instructions

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven

removed door, took out 8-9 screws, slid door upward, and removed. took out broken glass, and replaced.

First I removed the door from the double oven as instructed in the owner's manual. Then I removed the screws holding the door together. I removed the layers necessary to get to the inner door glass. Then reassemled it in the order that I had taken it apart. A total of 15 screws. My tip would be pay close attention to how you disassemble.
Not only did we save the cost of a repairman but because of Part Select we got the glass for less than half the price quoted to us from Kitchen Aid for the part and delivery.
Very satisfied with our experience with Parts Select

XLarge pizza tray in a 450 degree oven - slam the door & CRACK. Replacement glass arrived on Saturday - VERY FAST DELIVERY. Placed 2 allen wrenches in both hinges - open the door half way & lift up. Place the door on a towel. Removed 6 screws, lift & seperated the inner oven covering, removed the broken glass & cleaned inside & replaced with new glass. More time was spent cleaning & coming up with a tool to fit into the hinge

Relatively easy, my Jenn Aire model has a small 1/8 inch (est)hole under each of the door hinge assembly's, I inserted a an allen wrench on each side to hold the hinge. I then semi-closed the oven door, caution do it slowly until you get some resistance. You then pull upward on the door, caution it is heavy, you might have to jiggle it a bit. Once you have the door off you have to remove screws around the cover, the rest is intuitive. We took longer because we cleaned all the components.

fairly easy. took a while to reassemble. otherwise all was ok.

My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.

I just removed the door and change the glass. Really easy.

Removed Door, Took Door apart, Replaced glass, re-installed door. Pretty basic

Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

Repair was very easy, Alittle time consuming. Unscrewed the outer skin of the door and removed the pieces.

I did not take the door off the oven, i dissassbled it in place. all the visible screws on the door have to be removed. The "vent" air diflector or what ever it is , between the upper and lower doors has to come off also to access the screws that hold the front of the door on. The only confussion i had was the bracket that holds the third layer of glass. I forgot that it is held on with the same bracket/screws that hold the secound layer on.

1) Look for the part at partselect.com, make sure you have the model and part number ready. Once you find the part, don't order yet. 2) Start your do-it-yourself repair by removing the oven door. On each side below are two arms/hinges, look closely and you will find locks on each side. Use your finger or flat screwdriver to slide towards you (this is where you start clicking your camera in evey step). Once you did it, wiggle the door a little bit, make sure they're unlocked, then pull it out carefully and hold it tight since it's little heavy. 3) At this point, you only need the phillips screwdriver. Look for all the screws, and unscrew it all, one step at a time (again make use of your digital camera). Remove the parts one at a time until you take out the broken inner glass. Measure it against the dimensions shown in the partselect.com. At this point you feel comfortable putting it back in-reverse, then you order the part. It took me 3 days for the part to arrive, but it's no big deal. 4) It's a bit difficult for me the first time, I can't figure out how to put them back (that's why I recommended the digital camera), plus I have to clean the inside and the other two glasses so it took me 1-2 hrs. I assure you if you follow my instructions, 15-30 minutes max, no sweat. 5) My wife promised me $300 for the labor (competitive price), I'm still waiting though.....Good Luck