KDRP462LSS05 KitchenAid Range - Instructions

Repair was very easy, Alittle time consuming. Unscrewed the outer skin of the door and removed the pieces.

1) Look for the part at partselect.com, make sure you have the model and part number ready. Once you find the part, don't order yet. 2) Start your do-it-yourself repair by removing the oven door. On each side below are two arms/hinges, look closely and you will find locks on each side. Use your finger or flat screwdriver to slide towards you (this is where you start clicking your camera in evey step). Once you did it, wiggle the door a little bit, make sure they're unlocked, then pull it out carefully and hold it tight since it's little heavy. 3) At this point, you only need the phillips screwdriver. Look for all the screws, and unscrew it all, one step at a time (again make use of your digital camera). Remove the parts one at a time until you take out the broken inner glass. Measure it against the dimensions shown in the partselect.com. At this point you feel comfortable putting it back in-reverse, then you order the part. It took me 3 days for the part to arrive, but it's no big deal. 4) It's a bit difficult for me the first time, I can't figure out how to put them back (that's why I recommended the digital camera), plus I have to clean the inside and the other two glasses so it took me 1-2 hrs. I assure you if you follow my instructions, 15-30 minutes max, no sweat. 5) My wife promised me $300 for the labor (competitive price), I'm still waiting though.....Good Luck

I ordered the part online and after recieving it I downloaded the manual from kitchenaid online and it explain exactly how to replace this part and I followed the instructiones and it worked with not too much difficult . It took me about an hour between reeding the instructions and doing the job itself

opened door and secured the open position with a 3/8 allen wrench through the hole at the base of the support arm. (small bolt or other round, short object can be used). This locks the door in a 75% open position. Locking the door open allows easy lift and removal. Six screws and the door is apart. Clean and reassemble.

Had to screw off old terminal block & screw on new one

pull out the stove,took the top back panel off, take off wires one at a time on new spark module.. easy

Instructions were clear and the work was easy. Take your time and think about what you are doing, and you won't have any problems replacing the glass.

This 60 y.o. female had no owners manual. I completely relied on the information of this forum. *Recommend having a work area prepped before starting. I used a thick beach towel on the kitchen table. A layer of newspaper to catch all the dirty bits is a good idea.*You must remove the door - I followed the instructions using the allen wrench in the holes of the hinge. Open door. I put the short end of the wrench in the hole and leaned the long end against the oven rim. Start closing door and when almost closed, lift up to remove.*Place door handle side up on work surface to remove the 4 screws that hold outermost glass in place, 2 at top and two in brackets at bottom. Lay this aside in safe place on table. *Take off each layer to reach broken glass. *The hinge assembly has to be removed and the allen wrenches have to come out in order to accomplish this. Squeeze the hinge to take pressure off wrench to remove. Gloves help protect your hands for this step.Remove 2 screws each side. Keep each hinge next to the side it came from so you reassemble correctly.*If you have a phone with photo capability - I recommend you take a photo of each disassembly step. This saved me when it came to replacing the two brackets that hold the inner two pieces of glass. Clean all parts before reassembly (this takes the longest amount of time). I placed a thick cup towel in my sink and scrubbed. The cleaner I use for my glass range surface worked best. Dry thoroughly. When you get to the shattered glass remove it very carefully to avoid damaging the insulation underneath. I wish I had just purchased replacement insulation. Once the glass is replaced, everything goes back in reverse order. Now, here's the thing. I spent alot of time scrubbing. So, by the time I got to reassembly, I was bamboozled by the two 10 inch aluminum brackets that hold the two inner pieces of glass in place. So, to avoid any confusion, pay close attention to how these two brackets are placed or take pictures. This was an easy fix that went really well thanks to all the helpful info found here.

find the owner's manual & follow the instructions for inserting two allen wrenches (assuming that you cannot find the "removal tools" that came with the oven) into the holes near the hinges on the door, carefully & slowly close the door with the wrenches inserted until the hinges disengage from the wall mounted oven. Lift the door away (is rather heavy). It is necessary to remove panels from the front one layer at a time to reach the 3rd layer of glass (the inner most glass that is the rather easy one to break). Be slow and methodical. Not a challenge once you study the owner's manual for door removal instructions.

I used the manufacturers' manual as a guide and removed the door. This was not straightforward because the diagram was overly simplified. Once I figured it out, door removal was quite easy. I then took the door apart layer by layer (there are several), cleaning each part with oven cleaner, or detergent as I went. If not for cleaning, the repair would have taken half the amount of time. I then put the door together again and re-attached it. This was a little bit tricky but I got it to snap into place on the second attempt. Overall, this is a fairly easy repair and I do not have too much to add to existing comments. I would add the following: (1) Use work gloves to remove the broken glass. In fact, use gloves to handle all glass. (2) Take your time when re-assembling the door because the layers have to be lined up accurately for the screws to take and hold all of the layers together. In summary, I am very pleased with how this repair went. For 90 minutes of my time and $45, I was able to get the oven looking like new again.

I took the door off the hinge, laid it on the kitchen island and began to unscrew the outside screws. Be sure to have a bowl to place all the screws so none fall to the floor. I would recommend taking pictures with a camera phone as you dismantle each piece. The extra time was spent trying to remember how to put the 4 panes of glass back together....and if I had pictures to refer to it would have been easier. SECOND TIP- DO NOT have your husband help with any of this. I probably could have finished in less than 30 minutes if I was doing it by myself. Once he went to bed, the reassembly was much easier.

As I did not have a manual, I found all the website instructions very helpful. I had quite a hard time after installing the glass to figure out how to put it back together. The insulation between the oven glass is tricky to keep in tact. I also did not have allen wrenches to keep hinges open, so I used a variety of large bolts and screws. Finally after lots of hours, and almost calling a repairman, I did do it!

After a couple hours of frustration, I finally called the repair man and had it fixed properly. All the instructions I got from the the various websites didn't really address my model. Just getting the door off the over (with my type of lock) was a challenge. It is really important to have the proper tools for this job and I didn't have them. Live and learn.

I removed the oven door using the instructions in the book that came with the oven useing 2 allen wrenches as described. I called up the parts list for the oven door on my computer and made a copy.This was very helpful in removeing the door and getting to the broken glass and installing the new glass The one thing that that i regret was not ordering the insulation frame that went around the new glass. It was difficult getting it back in place.I would order this part if I have to do this again. I ordered the new glass on a Saturday and the new glass was delivered on Tuesday.Thank you for the great service. Bill- Texas

I did not remove the door. After removing as much broken glass as possible, I removed the two screws at the bottom of the door, pushing a bit against the plastic oven vents so the screwdriver could fit into the screw heads. I then removed the two screws on top of the oven door. This releases the outside of the door. I then removed the two bottom screws holding the bracket that holds the piece of glass fitting into the slot at the top. I bent back the tabs with pliers, cleaned the last bit of glass out of the slots, and then put the new glass in and bent the tabs back as much as possible. It actually was pretty tight. The rest is just cleaning and putting the pieces back together. Just be careful as the four screws that go into the top and bottom of the door are actually different from the other screws. Just make sure you keep all screws separated and use them as removed. Not too bad, just time consuming.