KERI201PWH0 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joyce from BALLWIN, MO
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
bake element out
use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from DEFIANCE, OH
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burner went out
Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from LYNNWOOD, WA
- Parts Used:
- WPW10308477
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element died
Followed instructions on urine that you provided. Instructions were great.
Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.
Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from The Villages, FL
- Parts Used:
- W11171119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from TRACY, CA
- Parts Used:
- WP3148952
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Over heating element.
Just turn off power , remover screws. Remove and plug in new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenny from GREENFIELD, IN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Removing an heating element that burnt into .
Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WALDORF, MD
- Parts Used:
- WP8053807
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Clothes would not fully dry in automatic cycle
1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Palm Beach Gardens, FL
- Parts Used:
- WP8053807
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven door sagged & wouldn't close properly
Took off oven door removed all screws to get old hinges out. Replaced with new hinges and put the door back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from APACHE JCT, AZ
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Elementwas burnt into
Watched the video and did as shown
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from ROCHESTER, MN
- Parts Used:
- WP3195546
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broke drawer bracket
Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from JACKSON, WY
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element non operational
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Duarte, CA
- Parts Used:
- W10355051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cleaner
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LARAMIE, WY
- Parts Used:
- 814381
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
Was this instruction helpful to you?
Thank you for voting!