KDRP463LSS0 KitchenAid Range - Instructions

First I looked at how I would get to the blower - this took 15 minutes. I removed the grills to access the burners. Then I removed the burners that took approx. 15 minutes. I then had to remove the knobs for the burners. Next I had to remove the front control panel which had 2 screws - (did not disconnect any wires but supported it). Next I had to remove the side trim. Next I removed 4-5 screws that secured the upper burner range top. Next I removed the side panels which has a braket on the lower forward side and 2 rear screws on each panel. Next I had to remove the aft backspash guard. At the back I had to remove a support braket that had several screws - then I had to remove the exhaust fan back panel guard. Next I had to remove approx. 7 screws on each side of the stove that supports the burner valves. Then I lifted the left side most closest to the blower. This gave me access just enough to remove the mounting screws (4) and to remove the 2 wires. There was some cushioning material which I found inadequate to prevent any vibration when the fan and the valve support top sits on the blower - so I doubled it. Then I reinstalled everything. This job took me 4 hours. I suggest calling a Kitchenaid repair technician and not doing this yourself. Unless you are a mechanically inclined and really like frustration.

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

removed double wall oven light lens install bulb replace lens fini

Pulled out stove and removed side panel, then removed old fan unit. Installed new fan unit and replaced side of stove then slide back in place, stove runs even more quiet than when it was new. And obtaining the new part from Partselect was even easier than dealing with a part store where you stand at the counter. This service really has the part down pat for us layman repair people.

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

After reading all the other entries, I decided that I could do this! My first hurdle was getting the oven door off the hinges. Mine were not like any of the others described. My son-in-law looked at them and couldn't figure them out. So, I found the original installation instructions and, lo and behold, they said to flip the lever (one finger operation) in each of the rectangular holes holding the door onto the oven and then lift up until the door comes off. I did it, and it did! Boy, is it heavy! From there I just followed everyone else's instruction about undoing the screws, washing the glass panels, lining up the screw holes to get it back together, etc. One thing that took me longer was that the steel panel needs to go back the way it came out, not flipped! When I washed the glass panel it held, I put it down wrong and then "installed" it backwards. Luckily, I have a double oven and looked at the other one to see what was holding up the re-assembly! I'm glad that one of the others mentioned that the glass on the "bottom", the one that broke, isn't held in my screws or steel plates -- nothing, so I wasn't surprised when I got to it and it was "floating" on the insulation. My white insulation was like a fine fiberglass and was easy to stuff back in around the rim of the new glass. Took me a little over one hour. So, no more wet rags on hot glass (you'd think after living 72 years that I would remember this!) The glass fit perfectly and my husband would have been proud of me -- that I tackled a job that he usually handled, and that I saved over $200 for a couple of hours of labor and travel time.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.

I simply removed the rear panel of the range and replaced the high temp. thermostat. The upper rear panel behind the back splash does not need to be removed.

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

ordered new broiler pan

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

Removed old fan by removing all screws except the back two lower screws - here I cut the flange on the old fan to remove. Drilled the back two bottom holes so as to fit over existing screws then replaced the top 3 and bottom 2 screws as well as power leads. Offset screwdriver is a must.