KDRP463LSS08 KitchenAid Range - Instructions

Remove and replace oven door hinges. Disassembly of oven door unit required. Step by step instructions available on youtube.

I pinpointed the location of the sound, took off the protective plate, felt it vibrating against the plate. I disconnected the power supply, and looked at the wirings and how it was connected, saw some burning residue surrounding the area of the Transformer. Then figured that I could simply replace this. I wrote down the Model and Serial number of the Stove, searched online, found this site. Located the part on the diagram, then simply ordered it. My part arrived in 3 days, and had the part replaced the next day. Couldn't be a smoother fix. Thanks.

First I looked at how I would get to the blower - this took 15 minutes. I removed the grills to access the burners. Then I removed the burners that took approx. 15 minutes. I then had to remove the knobs for the burners. Next I had to remove the front control panel which had 2 screws - (did not disconnect any wires but supported it). Next I had to remove the side trim. Next I removed 4-5 screws that secured the upper burner range top. Next I removed the side panels which has a braket on the lower forward side and 2 rear screws on each panel. Next I had to remove the aft backspash guard. At the back I had to remove a support braket that had several screws - then I had to remove the exhaust fan back panel guard. Next I had to remove approx. 7 screws on each side of the stove that supports the burner valves. Then I lifted the left side most closest to the blower. This gave me access just enough to remove the mounting screws (4) and to remove the 2 wires. There was some cushioning material which I found inadequate to prevent any vibration when the fan and the valve support top sits on the blower - so I doubled it. Then I reinstalled everything. This job took me 4 hours. I suggest calling a Kitchenaid repair technician and not doing this yourself. Unless you are a mechanically inclined and really like frustration.

Pulled out stove and removed side panel, then removed old fan unit. Installed new fan unit and replaced side of stove then slide back in place, stove runs even more quiet than when it was new. And obtaining the new part from Partselect was even easier than dealing with a part store where you stand at the counter. This service really has the part down pat for us layman repair people.

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

removed double wall oven light lens install bulb replace lens fini

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

I simply removed the rear panel of the range and replaced the high temp. thermostat. The upper rear panel behind the back splash does not need to be removed.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced

Removed old fan by removing all screws except the back two lower screws - here I cut the flange on the old fan to remove. Drilled the back two bottom holes so as to fit over existing screws then replaced the top 3 and bottom 2 screws as well as power leads. Offset screwdriver is a must.

I removed the Oven door, unscrew 10 screws, open up the dor case, clean all glass levels, replace inner glass, reassembled the door, reinstalled the door to the appliance.