KESC307HBL4 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clearly, the bulb was the problem. The gasket is an invitation to more trouble.
Simple. But beware changing just the bulb when the gasket is not secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brice from Spotsylvania, VA
- Parts Used:
- W10823697
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
left rear burner not working
I ran numerous tests to eliminate the on/off switch and to ensure the wires were not defective. Thus I came to the conclusion it must be the burner was defective. I ordered the part from parts.com. I received the part in less time than what was advertised. The part arrived in good condition. I placed the part in and it worked just like new.
Thank You
Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ernest from coplay, PA
- Parts Used:
- WP9781593
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
cracked inner door glass
removed 4 scews underside of door 2 more at top to remove door handle. than removed front door panel. removed inner sheild by bending 4 tabs.removed outside door glass than insideglass. reversed process to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominique from ASHLAND, MA
- Parts Used:
- W10823692
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dual inner element stopped working. The ceramic portion had a crack most likely from thermal stress over the years.
First I found a YouTube video for Maytag Range Repair – How to replace the Surface Element with Limiter - 6" - 1200W
The steps are very easy-
1. Open oven door and locate and remove 2 screws holding top cook surface. These are located near the top inside edge
2. Lift surface cook top and then remove 4 screws holding this section to the cook top. This may require 2 people but I was able to hold the cook top and loosen the 4 screws myself. Then put the cook top aside.
3. Take a photo of the element being replaced for wiring connections.
4. Removing the wiring and element holding clips was very easy. I used needle nose pliers for both
5. The clips have to be removed from the old element and put on the new one. Place them in the same locations
6. Make sure to reconnect the wires to the same pin locations. The replacement element I had the red (hot) wire pin 2b was in
A different location so I had to use the extension wire supplied with the new replacement element
7. Put everything back together in reverse order.
Easy peasy, took me about 40 minutes to complete the entire replacement and have it back in place working.
The steps are very easy-
1. Open oven door and locate and remove 2 screws holding top cook surface. These are located near the top inside edge
2. Lift surface cook top and then remove 4 screws holding this section to the cook top. This may require 2 people but I was able to hold the cook top and loosen the 4 screws myself. Then put the cook top aside.
3. Take a photo of the element being replaced for wiring connections.
4. Removing the wiring and element holding clips was very easy. I used needle nose pliers for both
5. The clips have to be removed from the old element and put on the new one. Place them in the same locations
6. Make sure to reconnect the wires to the same pin locations. The replacement element I had the red (hot) wire pin 2b was in
A different location so I had to use the extension wire supplied with the new replacement element
7. Put everything back together in reverse order.
Easy peasy, took me about 40 minutes to complete the entire replacement and have it back in place working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John M from Ponte Vedra Beach, FL
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Cracked inner door glass on self cleaning oven
Pulled the oven door out. Took the whole door apart and put it back together. The first time I put it back together the inner glass was still loose so I had to take it apart again and figure out how to hold everything together tightly. Your part was perfect. The glass was exactly the same as two others in the oven door. I wish I had instructions but when the parts fit it sure helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from DELANSON, NY
- Parts Used:
- WP9752294
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Replace element bake
Had to remove side panel then very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Thousand Oaks, CA
- Parts Used:
- WP9782033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Both left and right door hinges broke off their pins
The first time I took the door apart to see what part to order it was difficult. The second time I knew what I was in for and was more prepared. Replacing the hinges were no problem. It was taking apart the door that was more difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Monroe Twp, NJ
- Parts Used:
- W10823697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner Out Glass Top Range
Just as others said. Remove top holdown bolts with nut driver. Prop range top up.
Use a pair of plyers to remove wires (make sure you have a diagram to restore).
Use screwdriver to remove element hold down spring and wire holder. Replace element and replace wires and screws.
Use a pair of plyers to remove wires (make sure you have a diagram to restore).
Use screwdriver to remove element hold down spring and wire holder. Replace element and replace wires and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phillip from RUTH, NV
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
small inner burnner out
looked on internet on how to remove top. an easy fix after watching video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- welborn from hutto, TX
- Parts Used:
- WP9781593
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken inside door glass
took the door off, removed the screws, removed the back of the door, took the broken glass out, put new glass in, reassemble door, put door back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Queen Creek, AZ
- Parts Used:
- WP9781593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cracked inner door glass pannel
Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from UNIVERSITY PL, WA
- Parts Used:
- 9754103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Foam was very greasy and parts of the foam was burnt,
Removed the old and installed the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from POLK CITY, FL
- Parts Used:
- WP9781593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Inner door glass
Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from BOSSIER CITY, LA
- Parts Used:
- WP9750967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Only half of the broiler element would get hot enough to glow
First BE SURE TO TURN OFF THE CIRCUIT BREAKER!!! Remove the oven door if you need to get closer to the work. Then remove the screws securing the the element to the the oven. There were two on each side in the back where the element goes they the wall and two more that held the element to the upper surface. Carefully pull the element out to gain access to the wires and terminals. Gently pull each wire off one at a time, being sure not to allow the wire to get pulled back into the rear part of the oven. Reconnect each wire securely to the new element. Doubly check each connection! Then replace each screw and you should be set!
Was this instruction helpful to you?
Thank you for voting!