KESC300HBL8 KitchenAid Range - Instructions

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws inside oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.

It was very easy. Disconnect the electricity. Take the two screws out that hold the top in place. Raise the top and with the pliers change all the electrical connections and retaining bars. Install the two new burned tops. Lower the top and re-install the two retaining screws.

The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.

Pulled the oven out from the counters and unplugged the electrical cord. Unscrewed the three screws holding the center back panel on and removed the panel. Located the temperature probe in the upper left part of the oven and followed the wiring to where it was connected. Unconnected the wire from the connector. Removed the screw holding the probe and pulled it out from the oven. Put the new part on and screwed it to the oven. Connected the wiring to the connector. Put the panel into the holding brackets and screwed in the three screws. Plugged in the oven and put it back against the wall. Turned on the oven, set a temperature and watched to see if it stopped at the set temperature. Bake3d dinner and ate it.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

Removed burned out burner, replaced new burner tested works fine

ordered, came the next day and just slid it on the gas stem

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

Took door apart no problem had a little trouble putting it back together just one piece I put back wrong had to start over not to bad still took less then one hour

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

The repair was simple:
PartSelect always seems to have the parts you need and they get them to you quickly.
Baking element - I removed the two screws that hold the element to the back of the oven ( Philips head). Disconnected the spade type electrical connections from each end of the element. Note: use some type of clamp to hold the wires from pulling back into the outer section of the oven. I used wooden clothespins). Reverse the process to install new element.
Broiler element - I placed the shipping container over the new baking element to protect it. Then removed the four screws holding the top element to the back of the oven ( Philips head). Take care to mark the 4 wires for the broiler element. ( 2 for outer coil & 2 for inner coil) Clamp these wires also after disconnecting. Slide the 2 "L" shaped hangers out of there slots. When installing the new element connect the wires first then slide the "L" shaped hangers back into the slots. reinstall the 4 screws and your done. I did the repair with out removing the oven door ( ours is difficult to get back on ) with the door off the job will take less time and access will be easier.