KGST307HBL2 KitchenAid Range - Instructions

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

Remove the bottom panel and confirmed that the igniter was not lighting. Unsrcrew the igniter from the housing in the oven, then removed the back of the range and unplugged two leads from their conections and ran the wires through the insulated back wall of the oven. To replace the part just did the opposite of above. Piece of Cake. Want to say also that I was astounded at the speed in which I received my part. Ordered it at 3:30 PM on Friday afternoon and received it by 10 AM Saturday. And with standard delivery! Thanks!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Followed Mfgs instructions.

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

Open oven door. Remove covers from burner tube. Remove 2 screws holding igniter. Remove panel from back of range. Unplug 2 wires attached to igniter. Pull wires thru inside of oven. Reverse process to install new igniter.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.

Looked online and found it was probably the igniter which wasn't firing. An incredibly gratifying and easy experience with the self-fix. Worked on the first try just like new.

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr

Step 1. Always ensure appliance is unpluged from power source. 2 Remove oven door by open slighly and lift up be sure your hands are up from hinges they can snap back and injure fingers. 3. Have a cover on a flat surface and have a diagram of oven door, 4. Remove bottom screws and slide out top glass and side rails. 5 Remove top cover and insulation over glass. Beware of any jagged glass. 6. Incert new glass. 7. Be sure when replacing insulation and cover that cover in under tabs to ensure glass is firmly held in place repeat steps in reverse order. Took just 20 minutes to repair. I used a small electric screw driver.

I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.