YKESS908SS01 KitchenAid Range - Instructions

Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.

Getting at the part was difficult. The top and both side panels had to be removed to reach the blower. Once they were off, it was fairly easy to swap out the blower. The repair guy wanted $140 for the part and $160 to insall. I did it myself for $94! If you do it yourself, keep a good record of what screws came from where as you go. This makes re-assembly much easier.

Open oven dooor. With a philip screw driver remove the gasket plate at the bottom of the oven holding the seal gasket. pull seal gasket away from oven seal channel and clean surface before installing new seal. align seal pins to to seal channel holes be sure not to twist the seal insert pins in one at a time.Install lower bracket however you may want to wet the fray ends of the seal gasket prior to screwing in plate to keep the ends from moving away from the bracket when scrwing it in place.

Our double-oven is wall-mounted, so accessing the backside to change the wires (as shown in the instruction video) was not a practical do-it-yourself option. After turning off the circuit breaker and disconnecting the broken broiler element, it is pretty easy to pull the four connection wires through the backside of the oven, which allowed us to disconnect the slide clips. We attached twist-ties to each clip/wire before disconnecting to keep the clips/wires from pulling back behind the oven wall when moving the new element into position. We found it necessary to crimp a few clips onto the new element to make secure connections, but the rest of the project went pretty much as shown in the video and the new element works great.

Removed back of oven. Disconnected 2 connectors on each side of element. Removed screws that were too rusted to use screwdriver with vise grips. Removed old element, inserted new element through holes in rear of oven.Installed 1 screw on each side of element in rear and 2 screws in front where brackets support the front of the element.Put back panel back on. Push oven back in place, plug back in outlet.It works great and I didn't have to pay service man.

There were 4 screws to remove and 2 wires to disconnect. We placed the order on line for replacement. It arrived the next day. We simply installed the new element by connecting the 2 wires (very easy) and putting the 4 screws back in place. It works like new and was sooo easy.

The existing bake element was charred and in pieces so could not be pulled out. We destructively disassembled the range and pulled out the pieces along with the melted insulation. The wall behind was also scorched.

Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and connector back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Removed oven door for easy access. Removed 4 phillip head screws that held broiler element from top of oven. pulled wires a couple of inches out from back of oven and used flat screw driver to help separate the wires connecting the broiler from the oven. Did the opposite to install the new element,.
The best part of this operation was the fact that the part arrived from Part Select by Fed X the next day after ordering it all for a shipping cost of $8.75. Great Service Highly recommend Part Select.

First I cut off power ! 2 screws for oven trim,4 more to disconnect from cabinet. Hardest part was pulling oven out and pushing back in. I found a big box of correct size to rest it on so I didn't need to disconnect the powerline. 8 more screws to remove the back panel. 2 screws to remove the thermostat.Then put it back together. New part had arrived sooner than expected, cost of the part was less than a minimum service call would have been! I absolutly will use your site again.PS Wife was amazed and now thinks I'm a genious.

I first did a search with my issue, found out there were many others with the same issue. That then led me to see the part, a fuse / thermostat, was the culprit and easy to replace it seemed. But first called a service co. who confirmed my findings, and quoted a fix of a $2-300! So I bought the part; worse case I'd have someone else install. The web site noted the few screws to remove and a key suggestion to find a box of same height to easily slide out oven; I used a porter cable nail gun case which worked great. Took my time removing trim, mounting screws etc., slid out oven easy. Removed back plate and there was the older one. Removed and installed new in a minute. Spent more time cleaning around trim than actual install. What a great day it was. Wife was happy too!

took apart and empty the broken glass!
ordered parts
too many glasses and no insulation ( no insulation in oven door when taken apart!
Got the correct parts on order via a second sales person!
Installed glass hinges, insulation and closed the door! and instaleed the oven door!

The U TUBE videos were exstremely helpful!

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem

I removed the two stainless trim pieces (2 screws) and then two screws which hold the oven frame to the cabinet. Be careful to put a pad on your floor before you pull the oven out of the cabinet as there are sharp edges on the bottom of the oven. I removed apprximately 12 screws holding the back panel in place. The fixed set point thermostat is in middle toward the top of the oven cavity after removing the rear panel. Just remove two screws and slide the terminal connectors onto the new thermostat. Very easy job for someone who is not too handy.