YKERA205PB6 KitchenAid Range - Instructions

To access the hidden bake element you have to remove the warmer drawer and the left side panel (your left from the back of the oven). To remove the side panel you need to access 3 screws under the side of the glass top, to lift the glass top open the oven door and remove 2 screws from the bottom side of the glass top. Once the drawer and side panel are removed you can use a flat head screwdriver to pry out the false bottom on the front side of the oven and remove 2 more screws on the side so it drops down. Move the insulation out of the way and relase the element tray by prying out 2 tabs on the front side. Unplug the connectors from the element terminals and remove the bolt holding the element. Fold the side of the element tray down to remove the element. Reverse order to install.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

real easy one to take care of, when the drawer broke I thought it was more than what it really was, after looking at it and seeing the wheel was gone I ordered the part and it came very quick, drawer is now fixed.

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.

I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

I took out the two screws that held the oven handle in place inserted the glass in the door and replaced the two screw!!! That easy!

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.

Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.

Took off top and pulled out old element and plugged in the new one