KGRC707LBS0 KitchenAid Range - Instructions

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

very easy

I refered to what I had read on repair stories of broken glass...then went to fixing mine and before I new it I was done and glass replaced...it was very easy as long as you watch what you are doing when u take it apart and replace things the same as they were removed......thank you

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Pulled the oven out from the counters and unplugged the electrical cord. Unscrewed the three screws holding the center back panel on and removed the panel. Located the temperature probe in the upper left part of the oven and followed the wiring to where it was connected. Unconnected the wire from the connector. Removed the screw holding the probe and pulled it out from the oven. Put the new part on and screwed it to the oven. Connected the wiring to the connector. Put the panel into the holding brackets and screwed in the three screws. Plugged in the oven and put it back against the wall. Turned on the oven, set a temperature and watched to see if it stopped at the set temperature. Bake3d dinner and ate it.

I was able to order the part I needed. The faulty pad had a broken stem.Several pads came in a bag so if I have the problem again I will have the parts on hand. I bought some RTV glue suitable for items at high temperatures; used a probe to make sure the hole in the grate was clear and clean and glued the new pad in place.

ordered replacement glass. removed oven door. dismantled parts, replaced glass and reassembled door and reattached to oven.

repair failed; after much difficulty in accessing the small bolts that hold the 'spark igniters' in place; rear two were more accessible, front two proved impossible. Next step, invest in a new slide-in stove. The repair was a dad guess on my part; although designers often consider repair as a non-option, -sad but true.

The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

As a relatively handy person, I have built homes, and done every kind of repair you could imagine from plumbing to heavy construction. I never wanted to play with appliances, just couldn't read those diagrams well enough to feel comfortable. Parts select has changed my life and saved me so much money and I have repaired appliances in several of the homes with no issues using your videos and parts as my guide.

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

Replacing an oven igniter is one of the easiest repairs you can make to your oven. There are two igniters - one for the broiler and one for the oven itself. Oven Igniter: Start by removing the rear panel of the oven which attaches with a couple screws. Inside the oven, remove the "butterfly" shaped heat deflector (over the flame tube) which attaches with four screws. You now have access to the igniter. Remove the two screws which attach it to the bracket. On the rear of the oven, unplug the two spade connectors. Pull the igniter out from the front of the oven. Fish the wires for the new igniter through the same hole. Plug the 2 new wires back in. You can't mess this up - the wires have matching connectors and you can't get them confused. The broiler igniter is a little more complicated. You will have to remove the side panel of the oven to reach one of the connectors. It's just a couple more screws. The procedure is the same, but the wires are much harder to "fish" through the hole though. Unscrew the broiler igniter from the bracket and unplug the wires. Before you pull them out, attach a length of clothes hanger so that you pull the hanger into the oven from the rear. This way you can attach the new wires to the hanger and then pull them through to the back of the oven. If you don't attach something when you pull the old wires out, it is very hard to fish the wires for the broiler igniter to the rear of the oven. Good Luck!

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.