KGRT600HBL9 KitchenAid Range - Instructions

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Took the back off and put it in. It was a snap! Shouldn't have waited 1 year to do it!

Replaced damaged drawer roller: easy peasy!

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.

There are already good instructions here on doing the repair, so I will just add what I found important. 1) using penetrating oil and an impact wrench on the screws that hold the inner glass to the inside of the oven door - they were rusted tight. 2) the outside glass front sits on the front of the door, on top of the edges of the side pieces, even though it looked to me like the side pieces were meant to go over the edges of the glass - they aren't. The bare side edges of the glass aren't covered with any trim at all. The video on removing the oven door that matched the kind of hinges I had showed taking them off the door as part of disassembly of the door. I didn't find that necessary at all, and you probably won't either. Less parts to have to get back in place. The hard part to me was finding the correct disassembly video to match the oddball hinges, which isn't to say it's a bad design - actually it seems better that the other more common designs. Take out the two screws above where the hinges enter the range, and lift the door up, away from the range, and off. Easy peasy.

Video's did not show my door construction so I had some difficulty and surprises. One must disassemble and keep all parts in order of disaasembly with all screws for each part.separated. Be methodical and patient and it will all work out.

Remove old knobs and replace with new ones!

The replacement wiring harness arrived earlier than expected - good news. Once at the stove, I began the process of dismantling the range controls, but as no instructions were included with the part, this task was more time consuming than it needed to be. Nonetheless, I was able to remove the original harness. Next, I removed the replacement harness from it's shipping box to begin the installation. However, I quickly discovered that the wiring (both wires) had separated between the second block/pot and the third. From visual inspection, it appeared that the copper had simply broken off inside the block/pot. I did install the new harness to see if it would at least provide spark to ignite the two leftmost burners - it did. So at least 2 of the 4 burners will now light without using a match. I've ordered another replacement harness in the hopes that it's not defective, too. Partselect.com was quick to send a shipping label for the return of the first replacement and has promised a refund for the defective harness once it's returned.

removed door from range and slowly took apart until reached inner glass. there are three pcs of glass, front and two inner. was able to clean the inside which was dirty after 15 years of use. took alittle over an hour from start to finish including thorough cleaning.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Pop old one out and new one in

It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.

My son had first removed the 2 screws to disconnect the damaged element. He then removed the element
by pulling it out and disconnected the wires.

I was si grateful when he was able to connect the new igniter so we could have cookies for Christmas...thank you for your very prompt delivery of the element and the ease to reconnect it.