YKERI204PW2 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- RUSSELL from LEESBURG, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
large right front burner wasn't going on
turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & ordered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from BEND, OR
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
This burner on our range had no temperature control - it was either full-on or full-off
1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new infinite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Punta Gorda, FL
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Paint peeling from strip
removed 3 screws holding the strip and replaced with new strip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from KENNEWICK, WA
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
R/Front Range Element would not change to Med or Low setting. Stayed on full hot and burned food.
I disconnected power cord from house current. Removed back panels (2). I then removed round knob on front of range. I then removed the 2 screws holding the switch in place. After doing that, I gently removed the actual switch itself from back of face panel. I then separated the 2 elements of the switch.
I took new replacement switch and reinstalled the 2 parts of switch and placed back into hole in face panel. I reinserted the 2 front screws that holds the switch in place. I put the selection knob back on. However, the knob does not fit tightly. The shaft on the switch itself is to long, but the switch works fine. You do not even know that knob sticks out further than before. I plugged unit back into house current and tested range element to see if it works. It did so with no problem. I then replaced rear panels and secured all screws back to their original location and that was all there was to it.
No problem. Was a fast and effective installation.
I took new replacement switch and reinstalled the 2 parts of switch and placed back into hole in face panel. I reinserted the 2 front screws that holds the switch in place. I put the selection knob back on. However, the knob does not fit tightly. The shaft on the switch itself is to long, but the switch works fine. You do not even know that knob sticks out further than before. I plugged unit back into house current and tested range element to see if it works. It did so with no problem. I then replaced rear panels and secured all screws back to their original location and that was all there was to it.
No problem. Was a fast and effective installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from WARBA, MN
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would stay on when switch set to low heat
Unplug and pull out range.
Unscrew the back of the range with Phillips #2.
Unplug wiring harness from switch.
Unscrew the switch from the front of the range with P2 driver.
Install and plug in new switch.
Remove the spring steel knob retainer from shaft.
Cut off extra knob shaft with dremel to match others (there is a narrow segment at the proper length).
Reinstall knob retainer, knob, and range panels.
Unscrew the back of the range with Phillips #2.
Unplug wiring harness from switch.
Unscrew the switch from the front of the range with P2 driver.
Install and plug in new switch.
Remove the spring steel knob retainer from shaft.
Cut off extra knob shaft with dremel to match others (there is a narrow segment at the proper length).
Reinstall knob retainer, knob, and range panels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Clermont, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not reaching temperature
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from LISLE, NY
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Could not control temperature for 8" burner (front right).
The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Oklahoma City, OK
- Parts Used:
- 814381
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George E from OCALA, FL
- Parts Used:
- 3184020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
the fastener became loose and dropped into the stove
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
George Clark
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from MARION, OH
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner didn’t work right
Replaced switch. Works right now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from GREENBRIER, TN
- Parts Used:
- WP3148952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
could not control the temp of the element
take off back panel, simply unplug the old switch and plug in the new one. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FOUNTAIN INN, SC
- Parts Used:
- WP3148952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cooktop on and cooktop hot indicator lights stayed on.
Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.
Was this instruction helpful to you?
Thank you for voting!