KGRT500BAL2 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Marietta, GA
- Parts Used:
- WP95292
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bulb burned out
Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from San Bruno, CA
- Parts Used:
- WP3185804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westminster, CO
- Parts Used:
- WP3184533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fiber Gasket around Pyrex Light Lens was mis-shaped
All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ellen from Altamont, NY
- Parts Used:
- WP9782065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My stove had been taking an increasingly long time to warm up, and then would eventually would not warm up more than 315 degrees.
I researched the problem on the internet, and all of the data led me to believe I had a bad igniter. My husband and I viewed a youtube video about installing a new one, and then I read step by step instructions on another site. We thought we would be able to easily do this ourselves, so we ordered the part from PartSelect, and I received the part within a couple of days. After taking the back off the stove, and the pan off the bottom of the oven, we attached a string and pulled through the old wires, and then attached the new wires on the igniter and pulled them to the back of the stove and connected them. The part was exactly what we needed, and now the stove works like it did when it was brand new! I was very happy with the results! MEF
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from The Woodlands, TX
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber pads on bottom of grate broke off, grate was scratching stainless steel top
I just put the grate pads in the bottom of the grate. The repair was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Warren, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven light would not work--faulty socket
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Newnan, GA
- Parts Used:
- W10355051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
Baked on sauce
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Bucklin, KS
- Parts Used:
- WP9781049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original oven light lens had cracked and broken in two.
I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from HELENA, OH
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven drawer would not slide...because of worn out nylon roller.............
removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- todd from minneapolis, MN
- Parts Used:
- WP9751123
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat,no gas smell,no glowing ignitor
Remove diffusers in bottom of oven,remove two screws that hold ignitor in place.Pull oven out, to access back of oven,remove three screws holding vented panel in place.Remove panel,find wires coming from ignitor,pull connectors apart and remove old ignitor.Install new ignitor in reverse order.Too bad for my wife it works fine now,she had a new oven/range picked out!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Denver, CO
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing bumper pads
Original bumper pads NOT glued into the burner grates. Hence they began to disappear during routine use and cleaning. Very simple repair with a little glue this time around. But fairly expensive for a very small part set
Was this instruction helpful to you?
Thank you for voting!
Oven Light Would Not Work, Old Bulb Broken
Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WOODSTOCK, GA
- Parts Used:
- WP8053344
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven wouldn't heat above 300 deg. F.
I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rio Rancho, NM
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
grate pads not available from kitchen aide
Been looking for grate pads for 10 years and finally found you site and part # WPL 814323.
Wasn't sure that they would fit but couldn't even find new grates so decide to try them --Fit perfect.
Kitchen aide stove top gas with round grates. Used the drill to clean out the holes with broken pads still embedded.With clean holes the new pads just screwed in like the originals. Thank you very much
Wasn't sure that they would fit but couldn't even find new grates so decide to try them --Fit perfect.
Kitchen aide stove top gas with round grates. Used the drill to clean out the holes with broken pads still embedded.With clean holes the new pads just screwed in like the originals. Thank you very much
Was this instruction helpful to you?
Thank you for voting!