KEDS200YBL2 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christopher from Arlington, NE
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
When the oven was on we noticed the bake element had a 1 inch section that was bright red. Upon closer inspection, after the oven was off and the element cool, corrosion like damage was apparent where the element had been bright red.
Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marie from WATERBURY, CT
- Parts Used:
- W10291024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
my first order a small drip bowl
came only I had to order the set again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from BELLINGHAM, WA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replacing oven light and socket
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joanne from THOMASVILLE, GA
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loosen 2 screws
Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Raymond, NH
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
items in the oven were not baking properly. We discovered the bake elemnent wasn't working and looked defective in one part.
I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Chesterfield, MO
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
old heating element "popped"
Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!
Was this instruction helpful to you?
Thank you for voting!
burners wasn"t getting hot like they should
i just unpluged the old burner and slideed the new burners in place and they work great now like a new range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from CHARLESTOWN, IN
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from COVINGTON, GA
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove got way too hot
Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from PUTNAM VALLEY, NY
- Parts Used:
- WP8053344
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was overheating and locking the door. Codes indicated the temperature sensor could be the issue.
Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heriberto from AUSTIN, TX
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
THE OVEN WAS NOT HEATING TO DESIRED TEMPERATURE
DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Robert from Downers Grove, IL
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element arced bigtime so we figured it was time - 18 years old!
I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Rutland, VT
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires fom the old element .. connected them to the new element ... put the screws back ...and tested. problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Lawrenceville, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The original bake element cracked, causing sparks and a small, brief fire on the crack. Next, the element would not heat.
First I turned off the circuit breaker to the oven. Then, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches to disconnect the two wires. The connectors were tight, so required a little wiggling to disconnect the wires.
Upon receipt of the replacement element, I turned off the circuit breaker to the oven. Then, I reconnected the element wires, pushed the connect wires into the back of the oven, and rescrewed the unit in place. With the circuit breaker turned back on, I tested the oven. It worked great. Very easy!
Upon receipt of the replacement element, I turned off the circuit breaker to the oven. Then, I reconnected the element wires, pushed the connect wires into the back of the oven, and rescrewed the unit in place. With the circuit breaker turned back on, I tested the oven. It worked great. Very easy!
Was this instruction helpful to you?
Thank you for voting!