KERA205PBT1 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James.O from Newark, DE
- Parts Used:
- WP8523178
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lower Door Trim gets rusty
I have removed this piece once before and painted it,
but it is difficult to prepare surface.
I tried to replace the part without removing the door
but had difficulty getting the screws to line up.
So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.
Door Trim went on easily and the oven door went back on quickly.
Surprised they don't make this trim piece with rust proof material.
but it is difficult to prepare surface.
I tried to replace the part without removing the door
but had difficulty getting the screws to line up.
So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.
Door Trim went on easily and the oven door went back on quickly.
Surprised they don't make this trim piece with rust proof material.
Was this instruction helpful to you?
Thank you for voting!
Both right and left side trims were broken.
Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from PLAINFIELD, IN
- Parts Used:
- WP3148953
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The 8-inch burner only heated on high regardless of the temperature setting dialed in.
Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CONCORD, NH
- Parts Used:
- WP3148952
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The burner would not shut off.
Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Warren, CT
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Bad element replacement
Took off top and pulled out old element and plugged in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Dunnellon, FL
- Parts Used:
- WP8523178
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door bottom trim piece was rusty
Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SAINT CLOUD, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven sensor was not regulating heat set for oven
Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from SOUTH BEND, IN
- Parts Used:
- WP8523166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I broke a piece of the trim and had to replace it
took the handle off, replaces the side trim piece and replaced the handle. Very simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas H. from COCOA, FL
- Parts Used:
- WP9761958
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Block had melted.R
Removed old terminal block & replaced with new one. Very simple. Did NOT have to replace cover as stated you should. Shipping could have been a little faster. Will definetly try this site again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from SHILOH, IL
- Parts Used:
- WP9761958
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Electric contact connection melted, shorting out the range.
After unplugging electric service, loosened 3 Philips-head screws holding 3 wires from range and loosened 3 nuts holding wires from electric cord. Also removed 1 Philips-head screw holding grounding tab. Removed 2 Philips-head screws and removed the old block. Mounted new block with those screws and replaced and tightened all 6 wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patrick from HUGHESTOWN, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
temp sensor went oven not heating
the hardest part was moving stove to trplace part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruno from LE ROY, NY
- Parts Used:
- WP8523175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bottom piece of range rusty
took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph K from PAHRUMP, NV
- Parts Used:
- WP3196548
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The oven light shorted out causing the safety thermostat to blow.
Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light
Works great again...without the light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BURNSVILLE, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Temp inaccurate
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!
This was an easy fix for a seventy year-old like me!
Was this instruction helpful to you?
Thank you for voting!