KDRP407HSS11 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from Snoqualmie, WA
- Parts Used:
- WP9760587
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
There was an annoying buzzing sound coming from the bottom of the stove
I pinpointed the location of the sound, took off the protective plate, felt it vibrating against the plate. I disconnected the power supply, and looked at the wirings and how it was connected, saw some burning residue surrounding the area of the Transformer. Then figured that I could simply replace this. I wrote down the Model and Serial number of the Stove, searched online, found this site. Located the part on the diagram, then simply ordered it. My part arrived in 3 days, and had the part replaced the next day. Couldn't be a smoother fix. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Kingsport, TN
- Parts Used:
- WP4449259
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replacement of inner glass
Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAURIE from BILTMORE LAKE, NC
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The oven was over heating because it wasn’t reading the temperature
Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on
Was this instruction helpful to you?
Thank you for voting!
Oven door was difficult to open and close. The door would not close completely, and the heat would escape.
First, I watched the YouTube video which showed how to replace the hinges. Then I ordered the hinges which came in two days. Using nothing more than the instructions I watched and a Phillips screwdriver, lI removed the door, set it on the counter on a towel, removed four screws, and then removed the old hinges. The new hinges fit perfectly and were held in place with two screws each. Then the door was reapplied to the oven. The oven door now operated as if it were new. I wish I had attempted the repair much sooner, as we could have avoided the difficulty with opening and closing the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nadine from ALACHUA, FL
- Parts Used:
- WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
After using self cleaning feature oven wouldn't heat
I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from GARNER, NC
- Parts Used:
- WP9759243
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
E1 and e15
Removed locking device
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from MINNETRISTA, MN
- Parts Used:
- WP9759243
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Limit Thermostat had burned out due to high temp of self cleaning mode
1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PRESCOTT, AZ
- Parts Used:
- WP4451722
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
R&R broken inner door glass and insulation.
Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from STONINGTON, CT
- Parts Used:
- WP9760771
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
REPLACED NONFUNCTIONAL BROIL ELEMENT
EASY. FOLLOWED THE YOUTUBE INSTRUCTIONS ON THE WEBSITE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from TRENTON, NE
- Parts Used:
- WP9760771
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Didn't heat
Cordless drill removed 2 screws replaced element and 2 screws
Done. Didn't use new bracket
Done. Didn't use new bracket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from Wilmington, NC
- Parts Used:
- WPW10131825
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
All elements would heat to around 200 degrees, then stop
Disconnect the sensor harness and checked resistance on the sensor,should read around 1100 ohm I only got 25.The sensor is mounted in the oven cavity back wall below upper element,the door must be removed. Unscrew 2 Philips head screw,unhook the harness,install new sensor,reconnect harness,install screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from Keller, TX
- Parts Used:
- WP4449259
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken inside glass
unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LARAMIE, WY
- Parts Used:
- 814381
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Prairieville, LA
- Parts Used:
- WP4449259
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Cracked in oven door glass
Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.
Was this instruction helpful to you?
Thank you for voting!