KGST300FWH2 KitchenAid Range - Instructions

Replaced damaged drawer roller: easy peasy!

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceramic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.

I have KitchenAid convection oven that is about ten years old . The hinge on the left hand side broke so I had to replace it. It took me about 2 hours to get the job done because I cleaned the door as I went . The change out while fairly strait forward did take some time . A lot longer the some of the people said .

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

ordered new broiler pan

Pop old one out and new one in

My son had first removed the 2 screws to disconnect the damaged element. He then removed the element
by pulling it out and disconnected the wires.

I was si grateful when he was able to connect the new igniter so we could have cookies for Christmas...thank you for your very prompt delivery of the element and the ease to reconnect it.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.