KGST307BAL1 KitchenAid Range - Instructions

Removed two screws that attach the oven lighter to the burner. Removed the cover from the back side of the oven (3 screws). Unplugged the two wires from the end of the lighter. I taped a piece of string to the wire ends and pulled the unit out. Taped the new wires to the string, and pulled them back through the insulation. Reattached everything and THE OVEN LIT. Thanks, PartSelect, You saved me an expensive service call. Also, the replacement part arrived in less than 24 hours!

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

Take 4 screws off to remove oven pan, once pan is off , you can see the igniter. Take off two screws and remove old igniter. Be sure to run wires on new igniter where they were on the old igniter.

Pulled insulation out of the way to feed wires through. Might have helped to tie pull string to old wires but fishing them through was not to difficult.No need to cut wires; it is not a good idea to make unnecessary splices.

As a relatively handy person, I have built homes, and done every kind of repair you could imagine from plumbing to heavy construction. I never wanted to play with appliances, just couldn't read those diagrams well enough to feel comfortable. Parts select has changed my life and saved me so much money and I have repaired appliances in several of the homes with no issues using your videos and parts as my guide.

Replaced valve, 3 pipe connections 4 wire connections, still did not work, small flip up valve was set at off position, set to on, still did not work, replaced ignitor, bingo that was the real problem, reinstalled old valve, still working fine; returned new valve assembly for full refund! Thank You

I removed the door and I took it completely apart in order to replace the broken inner glass pieces. The door has about 30 separate pieces, so it is a meticulous repair and I recommend that you be fairly handy if you are going to attempt this. Something that seems as though it should be pretty simple took me nearly two hours to complete. I am happy to report that the result was a resounding success. The broken oven door glass had been affecting the oven temperature and as the result the baked foods were adversely affected. Cakes, pies, etc, would either be over or under cooked with no way to properly regulate the temperature. The inner glass is necessary in order to maintain correct oven function, so replacing it made everything work as designed once again.

Replaced both rollers....Quick and Easy!!

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine

Very simple, cleaned out what was remaining of the old rubber feet and just pushed these in. I didn't bother glueing them in as I didn't feel they would fall out. If they do, I'll go out and obtain the glue that is mentioned by others in this thread. Very satisfied.

I very simply replaced the gasket where it belonged and I was good to go!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.