Models > KESH307HBS5 > Instructions

KESH307HBS5 KitchenAid Range - Instructions

Jump to:

All Instructions for the KESH307HBS5
121 - 135 of 179
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mark from Washington, DC
Parts Used:
WP9781593
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Inner glass shattered due to dropping something on it
Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Elaine from Colorado Springs, CO
Parts Used:
WP9781593
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
I Broke The Inner Glass On My Oven Door With A Pizza Stone
I did the repair myself while my husband was at work. I lacked the brute strength to remove the door, so I ended up taking in apart while it was in place. Unfortunately, I only now noticed that instructions for installation were provided on your website. I did it without instruction, just making sure to note where screws had been removed so I'd be able to reassemble the works when I was finished. The worst part was loosening a couple of the innermost screws--even after a long soak in wd40, they were really hard to crack loose. Once I managed that, though, it went smoothly. Don't be intimidated; you can do this stuff yourself without calling--and paying--a repairman.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gus from Freeland, WA
Parts Used:
WP9781593
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Inner door glass broke from contact with cooler liquid.
I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the glass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marion from Centereach, NY
Parts Used:
WP9750967
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Heating element burnt out
Had difficulty removing the two screws holding element(range is eighteen years old.Screws were badly rusted)After that,it was a piece of cake
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Bloomington, MN
Parts Used:
WP9781593
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Broken Oven Glass
Per the instructions listed in your customer replies
Was this instruction helpful to you?
Thank you for voting!
Customer:
Warren from Mukwonago, WI
Parts Used:
WP9752294, WP9750967
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Little or no heat when baking
In my situation I thought that I needed an Oven Temperature Sensor so I started by replacing the Oven Temperature Sensor PS388521 -

PLEASE NOTE: You CANNOT reliably do a continuity check on the bake element described here until you have completed te first four steps!!

PLEASE NOTE: Access to the lower bake element is via the RIGHT SIDE PANEL!

To replace the lower heating element (aka the bake or hidden element). These instructions are specific for the KESC307xxxx:

1. Disconnect power to the oven.

2. Move oven from it's location to gain access to the right side panel.

3. Remove the oven drawer (if any).

3. Remove three screws holding the right side panel in place and remove panel. Two of the screws are on the rear of the range. The third is accessed via the cavity where the oven drawer is mounted.

4. CAREFULLY disconnect both wires connected to the element terminals.

5. Remove one screw (not shown) from Shield-HT (item 8 in http://bit.ly/O52AP2) and remove the shield.

6. Carefully pull back fiberglass insulation to reveal cover-access panel.

7. Remove two screws that hold the element to the cover-access panel (item 3 in http://bit.ly/NjvzOi).

8. Remove one screw holding the cover-access panel in place.

9. Remove both element and cover-access panel. NOTE: Observe the orientation of the brackets that support the element so you can install the new element correctly!

10. Installation is the reverse of these steps but make sure you replace the fiberglass insulation correctly or you will experience problems with heat transfer and a possible hot-spot on the side of the oven.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Grant from Alexandria, VA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from The Colony, TX
Parts Used:
WP9750372FF
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I was missing a temperature knob.
We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clarke from San Diego, CA
Parts Used:
9782081
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
oven would not heat past 170 degrees
Pulled the oven out from the counters and unplugged the electrical cord. Unscrewed the three screws holding the center back panel on and removed the panel. Located the temperature probe in the upper left part of the oven and followed the wiring to where it was connected. Unconnected the wire from the connector. Removed the screw holding the probe and pulled it out from the oven. Put the new part on and screwed it to the oven. Connected the wiring to the connector. Put the panel into the holding brackets and screwed in the three screws. Plugged in the oven and put it back against the wall. Turned on the oven, set a temperature and watched to see if it stopped at the set temperature. Bake3d dinner and ate it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kimberly from Sandusky, OH
Parts Used:
814229
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven Drawer Roller Snapped Off
Replaced both rollers....Quick and Easy!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from Carnegie, PA
Parts Used:
8009, WP3184533
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Oven Light bulb and gasket needed replaced
Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sam from Fairport, NY
Parts Used:
W10823699
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
One of the burner wasn't light up.
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Buford, GA
Parts Used:
WP9781049
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light lens broke when self clean cycle was used
I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward J from Baxter, MN
Parts Used:
W10823697
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
burner bad
looked it up on line how to change it. before I ordered part, to see how much of a job it was. was real simple to change, had no problem. also part select sent the correct part. Job went well
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonard from Kansas City, MO
Parts Used:
W10823697
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Front Burner Burnt Out
This job replacing the was so easy, it took about ten min,to do it thanks
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KESH307HBS5
121 - 135 of 179