KESH307HWH5 KitchenAid Range - Instructions

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

I refered to what I had read on repair stories of broken glass...then went to fixing mine and before I new it I was done and glass replaced...it was very easy as long as you watch what you are doing when u take it apart and replace things the same as they were removed......thank you

Unplug appliance first. Remove rear cover plate (only to disconnect burner plug). Remove plastic upper side covers. Open oven door & remove two screws holding burner top. Lift off entire top, flip upside down and change element.

We looked online for instructions, not sure how to "lift" the glass top.... There were 2 screws/hex head at the front of the range under the top that when removed allowed the top to be lifted up ..... the elements are on the underside, and with the removal of a few screws and unplugging the element connections (real easy) the burned out element was easily removed and the new one replaced... Less than 15 minutes for the whole operation...HOW COOL!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

12+ yr stove . double burner switch shorted out. replaced switch first.. shorted out agian. Then figured that the burner may be the source of the problem .. maybe the limiter was shot and overheated switch. purchased a new burner (Amazing 2 day delivery at std shipping rate!) removed 8 screws for the glass top & 5 for the burner control pannel in front. removed and replaced the burner with new one. Interestingly, the burner is held up in place to the stove top by a single flexable wire running under it. Was able to still use newly short switch. replaced top.. working fine ever since! Have not done this yet. But, in removing the control pannel identified an adhesive stip of foam tween the stop top and control pannel that got ripped up a bit in the seperation of the two. I suspect this was put there to prevent spilled water on stove top from leaking down to the inside of control pannel. Have to ask what I should replace it with. a caveman could do this. Disappointingly, my teens were not impressed, but happy to get a stove back so they could eat again. So for $150 I saved buying a $1.6k new stove.

In my situation I thought that I needed an Oven Temperature Sensor so I started by replacing the Oven Temperature Sensor PS388521 -

PLEASE NOTE: You CANNOT reliably do a continuity check on the bake element described here until you have completed te first four steps!!

PLEASE NOTE: Access to the lower bake element is via the RIGHT SIDE PANEL!

To replace the lower heating element (aka the bake or hidden element). These instructions are specific for the KESC307xxxx:

1. Disconnect power to the oven.

2. Move oven from it's location to gain access to the right side panel.

3. Remove the oven drawer (if any).

3. Remove three screws holding the right side panel in place and remove panel. Two of the screws are on the rear of the range. The third is accessed via the cavity where the oven drawer is mounted.

4. CAREFULLY disconnect both wires connected to the element terminals.

5. Remove one screw (not shown) from Shield-HT (item 8 in http://bit.ly/O52AP2) and remove the shield.

6. Carefully pull back fiberglass insulation to reveal cover-access panel.

7. Remove two screws that hold the element to the cover-access panel (item 3 in http://bit.ly/NjvzOi).

8. Remove one screw holding the cover-access panel in place.

9. Remove both element and cover-access panel. NOTE: Observe the orientation of the brackets that support the element so you can install the new element correctly!

10. Installation is the reverse of these steps but make sure you replace the fiberglass insulation correctly or you will experience problems with heat transfer and a possible hot-spot on the side of the oven.

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

Per the instructions listed in your customer replies

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the glass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!

Removed the right side panel, lifted up insulation, removed element and replaced with new.

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

One screw on each of the two cover plates removed, then element is pulled out enough to get at the connections. These are small blade connectors that slide off, two on each side, so 4 all together. The problem for me was that on one side the wires were to short and as soon as the blade connection was released the wire pulled back through the hole and was difficult to retrieve because it was hiding in the insulation. If I were to do this again I would use a small zip tie around the wire before disconnecting it so I would have something to pull it back out with.

Unscrew 3 screws across the front inside the oven door and the 2 screws on each side of the control panel. That allows for lifting the entire control panel from the front to access the switches from underneath. The old switch is held in place by the lug nut under the knob. Once removed, the 5 wires can be disconnected (carefully noting which wire connects to which terminal). The new switch is then connected, and then fastened back into place with the lug nut. The control panel is then re-secured by the five screws

Although I put 15-30 mins for repair, most of that was taking it apart only to have to put it back until I got the right part. It can be done in 15min or less. FIRST: UNPLUG THE RANGE or Shut the circuit breaker OFF. Remove two screws (1/4" nut driver) on the front lower edge of the cooktop. These are seen once you opent the top oven door. Lift up the top and pull out about two inches and disconnect the multiwire plug in connector. Lift the top off the range and place it upside down on a flat surface (talbe or counter) protected with a towel. Unplug the sliding connectors from the burner unit noticing the correct placement. Remvoe the two tabs (#2 phillips screwdriver) on either side of the burner unit noting location. Take the time to clean up all debris with a vacuum or soft cloth. Install the new burner, connect the two tabs, plug in the connectors, return the top to the range, plug in the multiwire plug, secure the two screws and plug the range back in and start cooking!