KESC300HBT8 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carol from BELLINGHAM, WA
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replacing oven light and socket
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BURLINGTON, NC
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
REPLACE INNER GLASS ON OVEN DOOR on KITCHENAID SUPERBA RANGE
There are already good instructions here on doing the repair, so I will just add what I found important. 1) using penetrating oil and an impact wrench on the screws that hold the inner glass to the inside of the oven door - they were rusted tight. 2) the outside glass front sits on the front of the door, on top of the edges of the side pieces, even though it looked to me like the side pieces were meant to go over the edges of the glass - they aren't. The bare side edges of the glass aren't covered with any trim at all. The video on removing the oven door that matched the kind of hinges I had showed taking them off the door as part of disassembly of the door. I didn't find that necessary at all, and you probably won't either. Less parts to have to get back in place. The hard part to me was finding the correct disassembly video to match the oddball hinges, which isn't to say it's a bad design - actually it seems better that the other more common designs. Take out the two screws above where the hinges enter the range, and lift the door up, away from the range, and off. Easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from W SPRINGFIELD, MA
- Parts Used:
- WP8190779
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
broken stove top glass
removed side and back strips after pulling out stove, removed top glass , installed new insulating tape around edges fitted new top on stove and replaced trim strips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Corona, CA
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Nylon roller on bottom oven shelf broken off
The nylon roller was very easy to install. Although rather pricey for what the part was, it was shipped immediately and got the job done. Took all of 5 minutes to do. I wish all my repair jobs were that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deb from Wentzville, MO
- Parts Used:
- 9782081
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven could not maintain heat. All elements were working, but would only heat up to about 250 degrees, then drop like a rock.
Took the back off and put it in. It was a snap! Shouldn't have waited 1 year to do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from MILWAUKEE, WI
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Storage drawer would not completely open.
Replaced damaged drawer roller: easy peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from morehead city, NC
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
electrical short from oven light.
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from UNIVERSITY PL, WA
- Parts Used:
- 9754103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Foam was very greasy and parts of the foam was burnt,
Removed the old and installed the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from batimore, MD
- Parts Used:
- WP9782033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
hinge on oven door broken
I have KitchenAid convection oven that is about ten years old . The hinge on the left hand side broke so I had to replace it. It took me about 2 hours to get the job done because I cleaned the door as I went . The change out while fairly strait forward did take some time . A lot longer the some of the people said .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from RIVERHEAD, NY
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken door inner glass
Video's did not show my door construction so I had some difficulty and surprises. One must disassemble and keep all parts in order of disaasembly with all screws for each part.separated. Be methodical and patient and it will all work out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Duarte, CA
- Parts Used:
- W10355051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cleaner
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from LEBANON, VA
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Light would not light
Pop old one out and new one in
Was this instruction helpful to you?
Thank you for voting!