KERC507EWH3 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from CLINTON, CT
- Parts Used:
- WP4448972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light bulb burnt out, the assembly was damaged by the rack sliding in and out
This is a microwave/ Oven slide in unit. You DO NOT need to slide out the unit, the repair can be done from inside the oven. Just be careful on pulling the wires from the unit so they do not break. I used shrink wrap over the joints but you can use tape as long as it can take the temperatures
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
Shattered inner oven glass.
Removed door from range. Removed the surrounding door molding. Removed the 5 retaining clips for glass and replaced inner glass. Reversed the above steps to complete installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Qiong from Mckinney, TX
- Parts Used:
- W10823694
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
outer ring of dual radiant burner doesn't work
Thanks for the previous viewer's tip, disconnect power, pushed the cook top out of the counter and used a wood block for the support. Unscrew the smooth top from the burner, remove old and plug in the new one. Connect power, test OK. Put everything back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Sandusky, OH
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Drawer Roller Snapped Off
Replaced both rollers....Quick and Easy!!
Was this instruction helpful to you?
Thank you for voting!
Broken dual broiler element, broken interior glass, missing drawer roller
Turned off electricity at breaker, slid stove out from wall. Disconnected unit. Removed back panel (4screws). Disconnected double broiler wires from the back. Unscrewed element bracket from back wall of oven (2 screws). Removed and replaced element and replaced screws to back wall of oven. Reconnected wires on the back of the oven where element connectors protrude from oven wall. Replaced back panel (4 screws). Removed oven door by pulling forward (no screws involved). Removed screws from bottom of door holding trim on (7 screws). Removed bottom trim and side trim. Removed front glass. Removed inner portion of door (it's just stacked together sandwiching some insulation). Removed track holding 2 glass panels (6 screws and pressure brackets). Removed one screw from corner of track. Removed and replaced inner glass. Lay door flat on floor front down to reassemble. Place glass insulation (looks like rope) around window opening. Lay the track containing he replaced glass down (side with most shallow recess). Replace 6 screws and pressure brackets. Replace large insulation and inner door panel. Reinstall front glass in slots under door handle. Replace oven door back. Reinstall side and bottom trim in reverse order to removal. Replace 7 screws along bottom of door. Reinstall door assembly to oven by sliding tabs back into the range. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from West Des Moines, IA
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Was this instruction helpful to you?
Thank you for voting!
Broken inside glass
Instructions on line were very helpful. The only problem was getting the screws loose on the clamps that held the glass in. If I was going to redesign this door I would use Hex head screws that can be removed with a nut driver. Most of the time for the job was taken up by cleaning off accumulated grease. You will be surprised how much gunk can get inside the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Wildwood, MO
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element had broken causing the oven not to heat up.
removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Hutchinson, KS
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven not heating up.
Remove two screws. Plug n play.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Jacksonville, FL
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom heating element broke in one part.
TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Blanket, TX
- Parts Used:
- WP9750213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element inoperative
Turned breaker off. Removed oven door for access, two screws loosened element, unplugged wires from element & removed element. Reverse order to install. Perfect fit. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from The Colony, TX
- Parts Used:
- WP9750372FF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I was missing a temperature knob.
We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Atlanta, GA
- Parts Used:
- WP9750213
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced defunct bake element in oven
The part came in 2 days even though I chose the least expensive shipping method. The hardest part was unscrewing the old screws that held the old bake element in place. We soaked them in WD40, and after a while were able to unscrew them. The new element slid in place and works just fine.
Was this instruction helpful to you?
Thank you for voting!