KGRT507FBL1 KitchenAid Range - Instructions

The repair was so easy. The part came in a box and as I expected it was an exact match. I closed my eyes...counted to three and behold the part was installed. I don't think that installation could have gone any better. I would buy again from this company if I needed parts for any appliance.

Replacing the igniter took care of the problem. I just wish I had made better notes about how the wire were routed. It would have saved time as I re-assembled everything. Th ejob itself was really easy.

I watched some videos on YouTube first that said you could flip a latch on the door hinges and remove the door entirely. On this older oven there was no latch, you just open the door to its first position and lift up and out to remove the door. Unlike newer doors leave this one face up on a table to work on it. Remove all (10?) of the screws along the bottom edge, pull away the side door trim pieces, then remove the outside panel of the door by lifting slightly then pulling downwards. Mine was actually a glass panel, so be careful. Remove the two screws holding the upper door trim down onto the hinge mechanisms and rotate the trim out of the way. Lift off the large metal cover to expose the first, outer glass, then remove the insulation, then remove the screws and clips holding down the metal frame around the inner glass. Clean everything well (I used a baking soda paste), then replace in the reverse order.

removed oven door from stove. Laid door on work table. Took screws out of the bottom. Flipped each layer over until I got to the interior glass. Removed broken glass and installed new glass. Flipped pieces back in place and put screws back in. Placed oven door back on stove. Easy!!

Replaced valve, 3 pipe connections 4 wire connections, still did not work, small flip up valve was set at off position, set to on, still did not work, replaced ignitor, bingo that was the real problem, reinstalled old valve, still working fine; returned new valve assembly for full refund! Thank You

The light lens was done by removing the pieces of the lense left in the stove, the bulb itself was stuck in the socket, it took pliers to bend and remove it. The replacement bulb has a mind of it own and comes on intermittently. The Interior door glass posed a bit more of a challenge. The door came apart just fine, but couldn't be put pack together as easily. It took three adults to try to press the pieces of the door back together, but to no avail. It is holding less one screw that could not be placed in the proper position due to misalignment of the holes. No pliers were used as they might have cracked the glass on the front of the door. The Glass Backsplash was very easy to install, however, the light, which is 26 inches long is not easy to come by at a reasonable price, so it was not replaced to date. Overall, it was a better deal than buying a new stove or paying for the warranty which could have paid for a new stove for as many years as I have owned this stove.

Replaced both rollers....Quick and Easy!!

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

Very simple, cleaned out what was remaining of the old rubber feet and just pushed these in. I didn't bother glueing them in as I didn't feel they would fall out. If they do, I'll go out and obtain the glue that is mentioned by others in this thread. Very satisfied.

slide the glass in. Thank you for having such a wounderful place to get what others said we can not get this glass. Thank you again

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I very simply replaced the gasket where it belonged and I was good to go!

Remove the bottom panel and confirmed that the igniter was not lighting. Unsrcrew the igniter from the housing in the oven, then removed the back of the range and unplugged two leads from their conections and ran the wires through the insulated back wall of the oven. To replace the part just did the opposite of above. Piece of Cake. Want to say also that I was astounded at the speed in which I received my part. Ordered it at 3:30 PM on Friday afternoon and received it by 10 AM Saturday. And with standard delivery! Thanks!

I was able to order the part I needed. The faulty pad had a broken stem.Several pads came in a bag so if I have the problem again I will have the parts on hand. I bought some RTV glue suitable for items at high temperatures; used a probe to make sure the hole in the grate was clear and clean and glued the new pad in place.

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine